Note: For International Buyers
Italiano:    Se non parlate inglese, si prega di copiare e incollare l'annuncio in http://translate.google.com
Greek:   Αν δεν μιλάτε αγγλικά παρακαλώ αντιγράψτε και επικολλήστε την αγγελία σε http://translate.google.com
Indonesian:     Jika Anda tidak berbicara bahasa Inggris, silahkan copy dan paste addvert ini menjadi penerjemah bahasa, seperti: http://translate.google.com
Spanish:    Si usted no habla Inglés, por favor copie y pegue el anuncio en http://translate.google.com
French:      Si vous ne parlez pas anglais s'il vous plaît copiez et collez l'annonce en http://translate.google.com
German:     Wenn Sie nicht Englisch sprechen kopieren Sie bitte und fügen Sie den Anzeige in http://translate.google.com

Lane Professional Airgun Regulator Parts & Kits
Exporting to 167 Countries (Jan 2024)


Please Note:   We manufacture regulators for all of the models listed below.
This advert is just for S300 through to S510 Super Lite
for other models please see our other adverts in our ebat shop - Lane Regulators.
S200, S200 Target, S200 Xtra. S300, S310, S400, S410, S500, S510, S510, HFT 500.
Ulti-Sporter, Air Arms "R" Regulated, SuperLight, TDR, GALAHAD. MPR
Biathalon / Sporter & Precision but must have front fill installed.
RN10,   Pro-target,  EVO,  EV2,   FPT900,
Older Models: TR100, XM100, XS100, NJR,   &  The Shamal.

MK9 'Lancet'
Professional Air Regulator Kits

The World Wide No1 for Air Arms Air Rifles

A "Must" - 'For The Serious Air Gun Enthusiast'.
'Whom Wishes To Tune Their Rifle & Gain The Very Best Results From His / Her Equipment'.

The Lane Regulator fitted correctly will: Stabilize Shot to Shot (Feet Per Second) Consistency at the muzzle,
Which leads to greatly Improved Accuracy & Air  Efficiency, Whether Competing in FT, HFT / Hunting or Plinking at the range.


Option ‘1’  
Air Arms Basic Regulator - Sub 12ft/lb
Kit Comprises Of:
1: Regulator.
2: Outlet Valve Stand off.
3: Spare Service Seal Kit for Regulator.
4: General Regulator & Fitting Instructions.
5: 1.5mm Breath Hole Drill Bit.

Suitable for
S300 Carbine / S300 Classic / S310 Carbine / S310 Classic
S400 Carbine / S400 Classic / S410 Carbine / S410 Classic
S500 Carbine / S500 Classic / S510 Carbine / S510 Classic
HFT 500.
Ulti-Sporter,  Super Light,
TDR / MPR - FT.
Biathalon / Sporter & Precision but must have front fill installed.

We very strongly advise that you to also buy 'Option 4' Outlet Valve Spring & Adjuster
in order to make re-balancing the Outlet Valve Assembly easier on the above models, if you don't have access to a harder Outlet Valve spring range.

Option ‘2’
Air Arms Professional Regulator Kit - Sub 12ft/lb
Kit Comprises Of All You Need:
1: Regulator.
2: Outlet Valve Stand off.
3: Spare Service Seal Kit for Regulator.
4: General Regulator & Fitting Instructions.
5: 1.5mm Breath Hole Drill Bit.
6: Outlet Valve Spring & Adjuster Screw.
7: Transfer Port Screw (To be cut down as required).
8: Transfer Port Drill Bit.
9:  2 x Hammer Spring for low pressure / high pressure tuning.
10: Extended Air Arms Full Seal Kit.
11: Extractor Screw.
12: Plastic Tube for help when setting Outlet Valve Spring Compression.
13: Air Arms Fitting Instructions.

Suitable for
S300 Carbine / S300 Classic / S310 Carbine / S310 Classic
S400 Carbine / S400 Classic / S410 Carbine / S410 Classic
S500 Carbine / S500 Classic / S510 Carbine / S510 Classic
MPR - MPR FT.
HFT 500.
Ulti-Sporter,  Super Light,
Biathalon / Sporter & Precision but must have front fill installed.

The Pro-kit is "Not suitable TDR / FAC Extra".

Option ‘3’
Pro Regulator Add On Kit (No Regulator).
1: Outlet Valve Spring & Adjuster Screw.
2: Transfer Port Screw (To be cut down as required).
3: Transfer Port Drill Bit.
4:  2 x Hammer Spring for low pressure / high pressure tuning.
5: Extended Air Arms Full Seal Kit.
6: Extractor Screw.
7: Plastic Tube for help when setting Outlet Valve Spring Compression.
8: Air Arms Fitting Instructions.

Option ‘4’
Outlet Valve Spring & Pot.
Not suitable for Xtra Models with Side Wheel Power Adjusters.

Option ‘5’  
Air Arms XTRA FAC
Kit Comprises Of:
1: Regulator.
2: Outlet Valve Stand off.
3: Spare Service Seal Kit for Regulator.
4: General Regulator & Fitting Instructions.
5: 1.5mm Breath Hole Drill Bit.

Suitable for
S300 Extra Hi-Power / S310 Extra Hi-Power / S400 Extra Hi-Power / S410 Extra Hi-Power
S510 Extra Hi-Power / S510 Extra Hi-Power / All FAC Models TDR, MPR
HFT 500, Ulti-Sporter,  Super Light etc...

What is the Lane MK9 Lancet Suitable For?

What Calibre Is It Suitable For ?
It can be used in all calibers
Yes:   .177   .20   .22   .25  9.mm

What Pressure Is The Regulator Set At ?
Each regulator is pre-tested and adjusted to suit your project 130bar.
Yes: Can Be adjusted   30bar  - to - 150bar

Is this product available world wide?
"YES - FREE POST - WORLD WIDE - Via Air Mail Tracked"
"Yes - Thousands of these regulators are now in use
and winning compittions week in week out in 167 Countries"


For far more details upon this series of regulators as well as for the most informative
and comprehensive information upon airgun regulators available in anywhere world wide
view all the relevant videos & FAQ’s upon Lane Regulators

Before you order, please be aware: The word Regulator is used in reference to this product being a Pressure Regulator and not a Power Regulator or tool for Adjusting Power Higher. The Regulator will only keep an airguns power FT LBS / Joules to the power at which it has already been - tuned to - at a - set working pressure. A Regulator, no matter what make or model, is nothing more or less than a very simple and basic pressure switch, which opens and closes to keep air pressure at the outlet valve near to a constant pressure down to its set working pressure. If you are unsure what a regulator is or the purpose of its function, there is an in depth article on 'What Is A Regulator' on the company manuals page. So like in the Article on the web page 'What Is A Regulator' please don't think that purchasing a regulator is an easy or simply fix for many woes. You should full understanding what an air regulator is, what it does and its principles of operation, along with those of your PCP and how they work and interact together.

Before you order, please be aware: Lane Regulators and other associated products are aimed at and for the gunsmith / airgun professional / serious enthusiast whom has both Machinery & Fitting Knowledge as well as practical experience of problem solving, in particularly air leaks (All items are tested prior to dispatch) whom ideally has their own or access to tools and workshop facilities. We do not know / judge you or your third parties skill set or the facilities available to you / them. This is yours decision to take. Many models of airgun vary slightly from country to country across the globe, and in some instances from batch to batch. You the customer must understand that a degree of alteration may be required to either or both the Regulator / Product / PCP to both fit and get the best out of what you have purchased.

Lane Regulators have been manufactured for 25+ years and are are sold on a -  self fit,  self service,  self maintain basis - As the greatest % of sales are overseas all regulators are tested prior to dispatch for leaks and set working pressure. All the manuals for pressure adjustment, stripping down, servicing and general maintenance are available as PDF Downloads upon the companies manuals page.

Lane Regulators are both sturdy and robust in design and will last a lifetime if looked after carefully. They are designed to be simple to service and maintain consisting of only three parts, of which two are working parts and only one moving part which engages with just two O-rings...