Description:
Portable integrated design, the overall compact and lightweight
Strong suction tin power, except tin easy and easy
High power heating, with fast heating function
Stable operating temperature and instantaneous temperature function
Storage tin tube made of high strength, high temperature resistant plastic
Especially for lead-free solder tin removal process
Details:
Model: S-993A
Power supply voltage: AC 220V 50Hz
Vacuum pump: diaphragm type
Power consumption: 100W
Heating parts: ultra-longevity imports of ceramic heating core
Temperature range: 350 ℃ ~ 450 ℃ (stepless)
Maximum pressure reached time: 0.2 seconds
Insulation resistance: 100 MΩ
Work: continuous
Suction nozzle specifications: ∮ 1.0mm
Instructions
1. The temperature of the suction nozzle of the tin gun is relatively high, so it should be used together with the tin gun holder to ensure safety.
2. The nozzle temperature can be set within the temperature range according to the work needs.
3. Aim the suction nozzle at the part to be removed, and then pull the button to remove the tin.
4. Before removing the plug, be sure to clean the nozzle and straw with a cleaning needle.
Precautions
1. When the new desoldering gun is used for the first time, it may emit smoke slightly due to the heating of the electric heating element, and it will disappear naturally after 10 minutes.
2. It is not allowed to knock, disassemble and install the parts of the electric heating and control parts arbitrarily.
3. To prevent the nozzle from being burnt and difficult to remove, please use lubricant or rust inhibitor.
4. At the end of the use of the tin gun, use a cleaning needle to clean the residual tin in the suction nozzle and the suction tube, and let the tin gun cool naturally in the air.
5. The tin remaining in the tin storage tank will reduce the tin absorption efficiency, so it should be cleaned up diligently.
6. During the process of tin absorption, the flux in the solder will become gas, and it will be adsorbed in the vacuum pump, so that the suction force will be reduced or it will not work. At this time, the vacuum pump will be disengaged, and the vibrating membrane and valve plate should be cleaned with alcohol. normal.
7. When the filter cotton is discolored, it must be replaced immediately to avoid reducing the tin removal effect.
Parts replacement method
How to replace the filter cotton
1. Hold the desoldering gun with your hand, pull the fastening seat (4) backward, and take out the tin storage cylinder (10).
2. When replacing the small filter cotton (5), take out the small filter cotton (5) from the fastening seat (4), put in the new small filter cotton, and put the tin storage cylinder (10) in the original direction. back into the suction tin gun;
3. When replacing the large filter cotton (7), take out the large filter cotton (7) from the tin storage cylinder (10), put the new large filter cotton in, and put the tin storage cylinder (10) back into the suction cylinder in the original direction. Inside the tin gun.
Product Structure
1 Desoldering gun shell
2 Hoses
3 Small springs
4 Fastening seat
5 Small filter cotton
6 Rear gasket
7 Large filter cotton
8 Bezel bracket
9 Bezels
10 Tin storage barrel
11 Front gasket
12 Connector
13 Heating core components
14 Suction nozzle
15 Cylinder head
16 Valve plate
17 Cylinder block
18 Diaphragm
19 Connecting rod
20 Balance weights
21 Motor
22 Button
23 Micro switch
24 Circuit boards
25 Wire clip
26 Grommets
27 Jacketed power cord
7. Accessories
Cleaning needle Φ0.8 1 piece
Cleaning needle Φ1.0 1 piece
2 small filter cotton
2 large filter cotton
ST-2091 Gun Holder 1
Noted: The heating element is a consumable product,please change it at your local , we will not provide extra one.