WINGXINE ASME-MDB 380kg Magnetic Encoder Bus Servo RS485 360-Degree Controllable Starting Point
Features:
- Suitable for servo controllers, wireless remote controllers for model airplanes and analog voltage control
- Alloy gear high-power motor with high-torque output
- Ultra-lightweight gearbox body made of aluminum alloy
- Easy to install and durable to use
Application:
- Heavy-duty motion control of arm joints and leg joints of large robots
- Industrial automation production line manipulator control
- Precise control of valve angle
- Large camera pan/tilt remote control
- Various occasions requiring large torque angle control
Rated Parameters:
- Rated voltage: 8~24V/DC (8V/MIN~30V/MAX, limit voltage)
- No-load current: <500mA (current limit: 5A. It is recommended to use a switching power supply or battery greater than 5A)
- Limit angle: ±180° or 0°~360° (MAX). Servo has electronic limit adjustment
- Control method: RS485 communications, level voltage 5V
- Control resolution: 360° corresponds to 12Bit resolution (4096); 32-bit MCU for ARM; digital port to read magnetic encoding data
- Material: Gear and shaft: alloy steel; gearbox body: cast aluminum
- Weight: 550g/1.2 lb
- Dimensions: 95 x 60 x 110mm/3.7 x 2.4 x 4.3"
- Mechanical life: >1,000,000 times/full load (conservative value)
Limit Parameters:
- Limit voltage: 7V~30V/DC (MAX)
- Current limit: 5A±0.2A (MAX)
- Working angle: ±180° or 0°~360° (MAX)
- Weight: 510g-560g/1.1-1.2 lb
Specifications:
- Model: ASME-MDB
- Starting torque: 380kg.cm max
- Holding torque: 340kg.cm max
- Rated speed (24V power supply): 0.5s/60°
Package Included:
- 1 x Servo
- 1 x 3Pin Cable For RS485 Communication
Note:
- Battery is not included.
Functions:
1. To set the center of the servo shaft, you can adjust the potentiometer setting by pressing the setting button. It can also be modified by serial port commands. Both ways are valid.
2. When the register type is flash, it will be automatically saved after modification. Data will not be lost after a power outage.
3. When the register type is RAM, the data will be lost after power off, and the initial state will be restored after power on.
4. Center adjustment: Press the SET button once to enter the setting state, and the indicator light turns into double flashes. Adjust the potentiometer next to the button, after reaching the desired position, press the SET button again to save the setting, and the memorized position will be permanently saved. Repeat this operation to update the central location.
5. Terminal resistors are required at the beginning and end of the bus, and jumpers are required as needed. Set the terminating resistor. Short circuit means with terminal resistance, disconnect means without terminal resistance.
6. Indicator light: The indicator light is breathing slowly in the state of no command, indicating that the servo is working normally. The indicator light flashes quickly when there is a command input.
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.