|
|
|
|
|
|
|
|
|
Please check fitment notes & description for accurate information.
2002-2004 Acura RSX 2.0L
2003-2005 Honda Civic 1.3L
2001-2005 Honda Civic 1.7L
2002-2005 Honda Civic 2.0L
2002-2004 Honda CR-V 2.4L
Oxygen Sensor's Location: How do I know the O2 sensor is good or not? Check engine light on A reduction in fuel economy.
Your catalytic converter fails unexpectedly
Exhaust emissions reach undesirable levels.
How to install the oxygen sensor? Step 1 - Some sensors are equipped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts. Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid stripping the old sensor upon removal. Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached. Step 4 - Its important that the wiring harness connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement sensors have a universal electrical connector that must be configured to the wiring of the old sensor.) Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends. Step 6 - Gently tighten the sensor while keeping wiring free from damage, these sensors need to be fairly snug to avoid leakage. Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed. Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harness. If the car has diagnostic trouble codes, they will need to be cleared. Must Know Before Buying: The following information is for instructional and guidance reference only. We try and make them as accurate as we can. If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks. Items that have been installed, altered or contaminated are non-returnable. 1. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty. 2. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return. The Price, Quality & Functionality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered.
Item Specifics | |
---|---|
Manufacturer Part Number | BMP05073500CP |
Type | Air Fuel Ratio Sensor |
Brand | Brakemotorparts |
Manufacturer Warranty | 1 Year |
UPC | 606462282932 |
Interchange Part Number | o2 sensor, 02 sensor, oxygen sensor car, wideband o2 sensor |
Other Part Number | 36531-PRB-A01A, 36531-PZA-A01A, 36531-PZA-L01A |
Superseded Part Number | KN4-382-A, OS2682-A, 5S5666-A, 5S4182-A, SU7-A |
Custom Bundle | No |
Modified Item | No |
Number of Pieces | 1 |
Fitment Type | Direct Replacement |
Thread Size | M18 |
Terminal Type | Blade |
Universal Or Specific Fit | Specific |
Attachment Method | Screw-On |
Connector Gender | Male |
Wire Harness Length | 18.98 IN |
Sensor Type | Heated |
Wire Quantity | 4 |
Output Signal Range | 0.2V To 0.8V |
Mounting Type | Threaded |
Pin Quantity | 4 |
Position | Upstream, Sensor 1 |
Feature | ESCP |
Type | Sensor |
Features | Direct Fit |
PayPal preferred.
Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay.
Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries.
All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days.
We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay.
The tracking number will be given for the customer to check the shipping status online (registered or faster service only).
We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout.
International Buyers Please Note:
Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.
Please check with your country's customs office to determine what these additional costs will be prior to bidding.
Serious Buyer Only! Please place bid or "Buy it now" only if you agree the price and terms of the product and no argument after the auction.
Do check the compatible chart above and the item you want before placing order.
Any question or problem, feel free to contact us please.
Your Best CHOICE of motor parts
Shop Category Picture Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us |
Upstream For 2002-2004 Honda CR-V Acura RSX Air Fuel Ratio 02 O2 Oxygen Sensor
Please check fitment notes & description for accurate information. 2002-2004 Acura RSX 2.0L 2003-2005 Honda Civic 1.3L 2001-2005 Honda Civic 1.7L 2002-2005 Honda Civic 2.0L 2002-2004 Honda CR-V 2.4L
Oxygen Sensor's Location: How do I know the O2 sensor is good or not? Check engine light on A reduction in fuel economy. Your catalytic converter fails unexpectedly Exhaust emissions reach undesirable levels. How to install the oxygen sensor? Step 1 - Some sensors are equipped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts. Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid stripping the old sensor upon removal. Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached. Step 4 - Its important that the wiring harness connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement sensors have a universal electrical connector that must be configured to the wiring of the old sensor.) Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends. Step 6 - Gently tighten the sensor while keeping wiring free from damage, these sensors need to be fairly snug to avoid leakage. Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed. Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harness. If the car has diagnostic trouble codes, they will need to be cleared. Must Know Before Buying: The following information is for instructional and guidance reference only. We try and make them as accurate as we can. If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks. Items that have been installed, altered or contaminated are non-returnable. 1. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty. 2. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return. The Price, Quality & Functionality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered.
Payment
PayPal preferred. Payments are expected within 7 days after the last winning auction is closed; Otherwise Unpaid Item Dispute will be filed with eBay. Shipping
Product will be shipped within 2 business days after full payment is received and verified. Delivery Time is about 3-7 business days to most of countries. All domestic orders will be shipped via USPS, UPS or FedEx from our US warehouse and usually arrives to your door in about 3-5 business days. We ship the package to your shipping address in eBay instead of the one in PayPal. Please tell us your shipping address if it is different from the one in eBay. The tracking number will be given for the customer to check the shipping status online (registered or faster service only). We are not responsible for any wrong or undeliverable addresses. Please verify and update your shipping address on eBay during checkout. Return Policy
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
All of our brand new items come with a 30-Days money-back guarantee.
It is the buyer's responsibility to understand the item description before bidding.
We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item backat his/her own cost.
Man-made damage by abuse or wrong operation is not covered by this warranty.
No product liability insurance is assumed.
Other Policy
International Buyers Please Note: Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Please check with your country's customs office to determine what these additional costs will be prior to bidding. Serious Buyer Only! Please place bid or "Buy it now" only if you agree the price and terms of the product and no argument after the auction. Contact Us
Do check the compatible chart above and the item you want before placing order. Any question or problem, feel free to contact us please. All rights reserved. |