• Please check fitment notes & description for accurate information.
  •  
  • 2000-2001 Lexus ES300 3.0L  2000-2004 Toyota Avalon 3.0L  2001 Toyota Camry 3.0L  2001-2003 Toyota Sienna 3.0L  2001-2003 Toyota Solara 3.0L
  •  
  •  
  • Oxygen Sensor's Location:
  •  
  •  
  •  
  • How do I know the O2 sensor is good or not?
  •  
    • Check engine light on
    • A reduction in fuel economy.
    • Your catalytic converter fails unexpectedly
    • Exhaust emissions reach undesirable levels.
     
  • How to install the oxygen sensor?
  • 2pcs Upstream for 01-2003 Toyota Sienna 3.0L Oxygen O2 02 Sensor Air Fuel Ratio

    Please check fitment notes & description for accurate information.

     

    2000-2001 Lexus ES300 3.0L
    2000-2004 Toyota Avalon 3.0L
    2001 Toyota Camry 3.0L
    2001-2003 Toyota Sienna 3.0L
    2001-2003 Toyota Solara 3.0L

     

     

    Oxygen Sensor's Location:

     

     

     

    How do I know the O2 sensor is good or not?

     

    • Check engine light on

    • A reduction in fuel economy.

    • Your catalytic converter fails unexpectedly

    • Exhaust emissions reach undesirable levels.

     

    How to install the oxygen sensor?

    Step 1 - Some sensors are equipped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts.

     

    Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid stripping the old sensor upon removal.

     

    Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached.

     

    Step 4 - Its important that the wiring harness connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement sensors have a universal electrical connector that must be configured to the wiring of the old sensor.)

     

    Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends.

     

    Step 6 - Gently tighten the sensor while keeping wiring free from damage, these sensors need to be fairly snug to avoid leakage.

     

    Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed.

     

    Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harness. If the car has diagnostic trouble codes, they will need to be cleared.

     

     

    Must Know Before Buying:

     

    The following information is for instructional and guidance reference only. We try and make them as accurate as we can.

     

    If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. 
    If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks.

     

    Items that have been installed, altered or contaminated are non-returnable.

     

    1. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty.


    2. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return.

     

    The Price, Quality & Functionality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered.



    Payment
    WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
    1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.
    Shipping

    1. Orders processed within 24 hours of payment verification.
    2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
    3. The images shown are not the actual item and are for your reference only.
    4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    Returns

    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!

    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
    4. Return shipping is to be paid by the Buyer.

    Feedback

    We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.

    2pcs Upstream for 01-2003 Toyota Sienna 3.0L Oxygen O2 02 Sensor Air Fuel Ratio

    Please check fitment notes & description for accurate information.

     

    2000-2001 Lexus ES300 3.0L
    2000-2004 Toyota Avalon 3.0L
    2001 Toyota Camry 3.0L
    2001-2003 Toyota Sienna 3.0L
    2001-2003 Toyota Solara 3.0L

     

     

    Oxygen Sensor's Location:

     

     

     

    How do I know the O2 sensor is good or not?

     

    • Check engine light on

    • A reduction in fuel economy.

    • Your catalytic converter fails unexpectedly

    • Exhaust emissions reach undesirable levels.

     

    How to install the oxygen sensor?

    Step 1 - Some sensors are equipped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts.

     

    Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid stripping the old sensor upon removal.

     

    Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached.

     

    Step 4 - Its important that the wiring harness connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement sensors have a universal electrical connector that must be configured to the wiring of the old sensor.)

     

    Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends.

     

    Step 6 - Gently tighten the sensor while keeping wiring free from damage, these sensors need to be fairly snug to avoid leakage.

     

    Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed.

     

    Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harness. If the car has diagnostic trouble codes, they will need to be cleared.

     

     

    Must Know Before Buying:

     

    The following information is for instructional and guidance reference only. We try and make them as accurate as we can.

     

    If Check Engine Light is on or an OBDII Trouble/Fault code occurs after installation, check the sensor with a voltmeter as below. 
    If the sensor is good, further diagnosis is required. There're many different codes for specific functional failures, which are NOT necessarily relevant to the sensor. Find out what the Code means before leaving any feedbacks.

     

    Items that have been installed, altered or contaminated are non-returnable.

     

    1. ONLY a defective sensor after tested by a voltmeter is applied to manufacturer warranty.


    2. 20% restocking fee is required if buyer bought wrong items due to not paying attention to fitment information and ask for return.

     

    The Price, Quality & Functionality of the O2 Sensor is fully covered under our warranty & return policy. However, refund for any labor cost, expense in a dealer shop or damage due to wrong installation is NOT covered.



    WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
    1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.1.We only accept PayPal.
    2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages.
    3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.)
    4.Payment must be received within 10 days as auction ended or order might be delayed.

    1. Orders processed within 24 hours of payment verification.
    2. We only ship to confirmed PAYPAL addresses. Your PAYPAL address must match your Shipping address.
    3. The images shown are not the actual item and are for your reference only.
    4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction!

    1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS!

    2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable.
    3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement.
    4. Return shipping is to be paid by the Buyer.

    We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.


    Copyright of hightechdeals8. All rights reserved.


    Shop Category