Plastic Fuel Gauge Interface Module Ohm Range Converter for Fuel Tank Interface
Product Description:
Material: Plastic
Product Size (Length * Width * Height): 35* 20*16mm
Packing Size: 12*9.5*2cm
Gross Weight: 0.1kg
Net Weight: 0.05kg
Features:
★As the Interface Between the Fuel Transmitter and the Meter, It Can Read Any Fuel Transmitter and Is Suitable for Any Electricity Meter.
★Accurately Correct the Unstable Motion Caused by Ohm Mismatch and Fuel Sloshing, and Customize the Calibration for Empty, Half-level and Full.
★the Fuel Gauge Is Designed for Specific Ohm Range.
★Different Car and Meter Manufacturers Use Different Ohm Ranges to Properly Operate Their Meters. This Can Cause Problems for People Who Update Their Vehicles with New Gauges or New Fuel Tanks and Fuel Transmitters.
★This Module Will Allow You to Use the Stock Transmitter with Any Fuel Gauge and Vice Versa.
The Package Includes:
1x Fuel Gauge Interface
Important Instructions:
① Install the Module in a Clean, Dry and Cool Place.
②Connect the Wires As the Guide Photo Above
③Using the Storage Mode, Program and Store Full, Half, Empty and "Power on" Positions.
④Use the Power-on Mode to Program How You Want the Instrument to Operate When the Car Starts.
⑤ Run and Check in the Run Mode.
⑥When Adjusting the Screw, Move the Pressure Gauge from Full to Empty to Avoid Hysteresis Error.
⑦some Meters Move Very Slowly. Please Wait for the Time to Stabilize.
⑧the Tank Sensor Must Have the Same Grounding As the Fm101, Otherwise It Will Cause Unstable Readings.
Store Mode
①Turn off the Power Supply. Wait for 5 Seconds. Press the "F" Switch and Turn on the Power, Then Release the "F" Switch.
②Only the Red Led Will Light up
③Set the Fuel Resistance to the Full Position. Use the Calibration Screw to Adjust the Meter to Full, Press the "F" Switch and Then Release It.
④Set the Fuel Resistance to 1/2 Gear. Use the Calibration Screw to Adjust the Meter to Gear 1/2. Press and Release the "H" Switch.
⑤Set the Fuel Resistance to Emptv. Adjust the Meter to Be Emptied Using the Calibration Screw. Press the "E" Switch and Release It.
⑥ Adjust the Calibration Screw to the Position Where You Want Gatne O When the Car Is Started. (Usually This Is the Position of the Pointer When the Car Is Closed)
Press "E" and "F" Simultaneously and Then Release.
Boot Mode
① Shut down. Wait for 5 Seconds.
②Choose Where You Want the Instrument to Start When the Car Starts (Usually the Instrument "off Position")
If You Want the Meter to Start from the Transmitter Position. (Suitable for Damped Bimetal and Cross-coil Meters)
Press the "E" Switch to Turn on, and Release the "E" Switch.
If You Want the Meter to Start at the Preset Position (Set in Step/6 of the Storage Mode). (Applicable to Instruments Without Damping) Press the "H" Switch and Turn on the Power, Release the "H" Switch.
③the Green Led Will Light up.
Operating Mode
①Turn off, Wait 5 Seconds, and Then Turn on.
②the Green Led Will Light up.
Type | Fuel Gauge Interface |
---|---|
Brand | Unbranded |
Manufacturer Part Number | Does Not Apply |
Warranty | 2 Year |
Fitment Type | Direct Replacement |
Material | Plastic |
Product Size | 35* 20*16mm |
Packing Size | 12*9.5*2 CM |
Gross Weight | 0.1 kg |
Net Weight | 0.05kg |
Features | N/A |
Display Type | N/A |
Unit of Measure | N/A |
OE/OEM Part Number | N/A |
Needle Color | N/A |
Color | Black |