Specification:
 

Type :Strut & Spring Assembly
Quantity:   2 PCS
Interchange Part Number:    172208、172207
Placement on Vehicle:   Left, Rear, Right
Fitment For Type :   Direct Replacement
 

Reference OEM Number: 172208、172207

Fitment For:

1x Rear Driver Side Strut w/ Coil Spring Assembly - 172208
1x Rear Passenger Side Strut w/ Coil Spring Assembly - 172207

Package Contains:
 

MAKE    MODEL    YEAR RANGE    SPECIFIC DETAILS
For toyota    CAMRY    2004 - 2006    All Models
For toyota    SOLARA    2004 - 2006    Models Mfg. Before June 2006
For lexus    ES330    2004 - 2006    Without Adaptive Variable Suspension

Warranty:
 

30 days free return and exchange
5 years warranty

Time to replace your struts if you are troubled by bellow:

The car makes unusual noises.
The car sink when the road is bad or load is heavy. 
Oil Leakage. 
Frequent and irregular tire wear. 
It's hard to control the car. 
Poor stability makes you feel very uncomfortable.

How to Install :

Step 1: Before You Lift the Vehicle, Loosen Lug Nuts One Full Turn.
Step 2: Jack up Vehicle and Use Jack Stands for Safety & Remove the Tire from the Rotor.
Step 3: (Wheel Alignment Is Necessary After Strut Replacement.) Marking the Position of All the Bolts Will Help Keep the Alignment Close to Original and save Time Aligning. Use a Colored Pencil to Mark the Old Strut on the Bolt.
Step 4: Use Penetrating Oil (Such As Wd40) to Coat Any Rusted Fasteners, Let Soak for Approximately 1 Hour.
Step 5: (Optional) While Waiting for Oil to Soak, Take This Time to Inspect All Other Components That May Need Replacement (Brake Pads, Rotors, Brake Hoses, Ball Joints, Cv Boots, Tie Rod Ends, Bushings, Sway Bars, Etc).
Step 6: Remove Any Brake Line or Wire Attachments from the Strut Body. Do Not Disconnect Brake Lines (If Possible)! Opening Brake Lines Will Require Bleeding of the Brake System.
Use Extreme Caution When Removing Brake Lines from Your Struts, As Any Damage to Your Brake Line Can Result in Expensive and Time Consuming Repairs.
Step 7: Remove Sway bar Attached to the Strut Assembly or Control Arm.
Step 8: Remove the Tie Rod (Only If It Attached to the Body of the Strut, If Not Leave It Attached to the Steering Knuckle).
Step 9: Remove the Strut to Knuckle Bolts at the Bottom of the Strut. on some Vehicles, the Brake Caliper and Rotor May Need to Be Removed to Gain Access.
Step 10: Remove the Upper Mounting Plate Bolts Located in the Engine or Trunk Compartment. Do Not Remove the Center Retaining Nut! It Is Not Safe to Unload the Spring from the Assembly in This Position.
Step 11: Carefully Remove the Old Strut Assembly from the Vehicle. Be Very Cautious Not to Let the Strut "Drop" down on Your Brake Line, Rotor or Drum.
Step 12: Install the New Complete Strut Assembly in the Reverse Order As Above (Steps 11-6). Using an Anti-seize Compound on All Fasteners Is Suggested.
Step 13: Carefully Double Check Your Work and Make Sure Everything Is Tightened to Manufacturers Torque Specifications.
Step 14: Replace the Tire the Rotor and Tighten to Manufacturers Torque Specifications.
Step 15: Slowly Lower the Vehicle down After Removing the Jack Stands. Pay Very Close Attention to Any Odd Sounds When the Vehicle Is Lowered Onto the New Complete Strut Assemblies.
Step 16: It Is Very Important That You Immediately "Road Test" Your Vehicle Right Away to Ensure That Installation Was Done Properly. Listen and Feel for Common Signs of Incorrect Installation While Driving Slowly over Speed Bumps, Rough Road or Potholes.