Vogtland Lowering Springs Mercedes CLS W218 250, 350 25mm 952039

The description of this item has been automatically translated. If you have any questions, please feel free to contact us.


Vogtland suspension springs 

suitable for the following vehicles:

Vehicle:           Mercedes-Benz CLS
Type: C218   350, 250CDI, 350CDI
Year of construction: from 01.11 ->
Lowering:     VA: approx. 25 mm, rear: approx. 25mm
Max. axle loads:Front axle: 1160 kg, rear axle: 1200 kg
Clues: 1, 7, 15, 21    <- Important! For details see below!
Art. No.               952039
 

Are you not sure if the springs fit your vehicle?
No problem! Please contact us with the relevant vehicle data


Additional note:

1=The lowering amount is reduced by the factory lowering amount. 21=All wheel/tire combinations approved by the wheel testing centers can be used. The requirements in the wheel report or Wheel ABE must be observed, with the exception of the requirement for standard chassis.


Including expert report. You are also welcome to contact us in advance by email. 
Personal and telephone advice from our team, even after the purchase 


Product description:

Lowering springs make Vogtland 

With VOGTLAND sports spring sets - - upgrade your vehicle:
rasant appearance with maximum driving pleasure. Whether in normal operation with pleasant driving comfort or at the limit with sporty, progressive tuning.
 The special driving dynamics are achieved through the innovative spring design.

VOGTLAND Compound Spring Rate
The shortening of the spring travel requires a special suspension characteristic,
which is derived from racing. The VOGTLAND compound spring consists of two different spring rates:
an initial and an end rate. These specially tailored to your vehicle type,
The interacting characteristics ensure balanced driving comfort and more driving dynamics, even when driving in a sporty manner. The lowering ranges from 25 to 60 mm.

Increase your agility and driving pleasure and experience your vehicle in a whole new way!

Wedge shape
Try lowering the front axle a little lower than the rear axle.
And you will be amazed at how the particularly dynamic wedge shape transforms your vehicle into a visual power package.
This is pure power! Spring sete with only two springs for the front axle. Looks good and is inexpensive!

 

Vogtland Notes

No. Notes   No. Remarks
1. The lowering amount is reduced by the factory lowering amount.   1. The measure of the lowering will be reduced by the measure of the sport suspension.
2. Wedge shape: The lowering of the front axle depends on the equipment and engine variant.   2. Wedge form: The lowering of the front axle depends on the equipment and weight of the engine.
3. From chassis number 21234.   3. As of chassis number: 21234.
4. For fine-tuning, please use Mercedes-Benz spring plate pads, which are available in various thicknesses (8 - 23 mm).   4. For fine tuning, please refer to the Daimler Benz spring insolators available in different heights (8-23 mm).
5. Reinforced version (heavy duty) for fully equipped vehicles with more than 4 cylinders.   5. Heavy duty for models with full equipment and more than 4 cylinders.
6. For vehicles with a load-dependent brake force distributor, a demonstration is required despite the ABE.   6. A presentation is necessary despite ABE for vehicles with a load depending brake power distributor.
7. Not for vehicles with level control / air suspension.   7. Without self-leveling / air suspension
8. For vehicles with Tiptronic, Multitronic, increased lowering possible.   8. Additional lowering may occur on vehicles equipped with automatic transmissions.
9. Only for fully equipped vehicles.   9. Only for vehicles with full equipment.
10. With XR3i no additional lowering, just tighter tuning.   10. XR3i does not lower, only the adjustment becomes more sportive.
11. For vehicles with 6 cylinders, e.g. Golf III VR6, a conversion to sports dampers is recommended, included in the VOGTLAND complete suspension.   11. Vehicles with 6 cylinder engines require sport shocks.
12. Not for: Break, Caravan, Turnier, T-Modell, Touring, Variant, Avant, Station Wagon, Traveller, (Estate).   12. Not for station wagons.
13. From ABE no. 9138/2.   13. As of ABE number 9138/2.
14. Up to 8.79 use spring plate with the number: 171412341A.   14. Up to 8.79 please use spring cap number 171412341A.
15. Not for four-wheel drive.   15. Excludes 4 wheel drive.
16. Possibly. Modified spring plates [and possibly other parts] must be used on the front axle. Either the spring plate with the VW part number 1H0412341 (large) or 357412341 A (small).   16. Volkswagen springs caps [and probably further Parts] might be necessary: ​​1H0412341 (big) or 357412341 A (small).
17. Shortened sports shock absorbers required. These are already included in the VOGTLAND complete chassis.   17. Shorter sport shocks are required. The VOGTLAND suspension kits are covered with these shocks.
18. Not for series sports suspensions.   18. Not suitable for serial or sport suspension.
19. Front axle springs only, rear axle torsion bars (or standard spring element).   19. Only front springs, torsion bars (or standard spring) on ​​the rear axle.
20. Rear axle springs only, front axle torsion bars (or standard spring element).   20. Only rear springs, torsion bars (or standard spring) on ​​the front axle.
21. All wheel/tire combinations approved by the wheel testing centers can be used. The requirements in the wheel report or Wheel ABE must be observed, with the exception of the requirement for standard chassis.   21. All wheel/tire combinations are allowed which are released by the wheel type testing institution. The conditions in the wheel approval have to be kept, except when suspension is required.
22. With adjustable complete suspensions, the damping forces can only be adjusted on the front axle when installed.   22. At the VOGTLAND adjustable suspension kits only the shock valvings in the front are adjustable.
23. Due to vehicle-specific tolerances, it is possible that the stabilizer and drive shaft come into contact. For coilover suspension: Item no. 968550000, stabilizer kit, without xenon. For complete chassis: extended standard coupling rods (VW/Audi).   23. Due to vehicle-specific tolerances a contact between the drive shaft and the anti-roll bar might occur. In such case it is required to install a modified anti-roll bar. For Coilover Sets use Order No. 968 550 000 (Anti-roll bar conversion set without Xenon headlights). For Suspension Kits use a longer steering rod from your VW/Audi dealer.
24. VA/HA threaded spring struts (height adjustable).   24. Height adjustable at the front and rear axle (threaded strut housings).
25. VA/HA height adjustable (VA threaded spring legs, HA springs with height adjustment plus shock absorbers).   25. Height adjustable at the front and rear axle (front axle threaded housings, rear axle threaded spring perch and separate shocks).
26. Only front axle height adjustable, rear axle spring and shock absorber.   26. Only height adjustable at the front axle (threaded strut housings), springs and shocks at the rear axle.
27. With standard tires possibly. Spacers required.   27. May require the use of wheel spacers with equipment tires and wheels.
28. The level control must be shut down.   28. Self-leveling must be shut down.
29. Front axle height-adjustable coilover spring strut, rear axle sports shock absorber (adjustment of the rear axle via torsion bar).   29. Height adjustable at the front (threaded strut housings), rear axle is adjustable with torsion spring adjustment.
30. Damper adjustable when installed.   30. Installed shocks can be adjusted when installed.
31. Damper can only be adjusted when removed.   31. Installed shocks cannot be adjusted when installed.
32. The front direction indicators (§ 76/756 EC) must have a minimum height of 350 mm. Alfa part number: 46226968.   32. The front turn lights (§76/756 EG), must be the min. height from 350 mm. Alfa part number: 46226968.
33. Production date 4/02 (piston rod thread visible), from 4/02 (piston rod thread covered).   33. For vehicles manufactured before 04/02, the piston rod is fastened to the support bearing with an arched disk (piston rod threads visible). Models built after 04/02, piston rod threads not visible.
34. Only for use with vehicles with rear shock absorber mount M10 (1.0i, 1.2i, 1.7Di).   34. Only for vehicles which have rear dampers mounted below with M10 (1.0i, 1.2i, 1.7Di).
35. Use only for vehicles with rear shock absorber mount M14. (1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi)   35. Only for vehicles which have rear dampers mounted below with M14 (1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi)
36. Front shock absorber: complete spring strut with item no.: 960422, 960423, 966322, 966404, 966406, 966407, 969419, 969422, 969423, 960462.   36. Front shock: complete suspension strut. Part number: 966404, 966406, 966407, 966322, 960422, 969423, 960423, 960462.
37. Front shock absorber: spring strut cartridge   37. Front shock: cartridge
38. Dampers are only suitable for European vehicles.   38. Damper only suitable for European cars.
39. If the drive shaft diameter is more than 42 mm, the max. tested lowering by approx. 15mm.   39. If the driveshaft diameter is greater than 42, mm the max. approved lowering is reduced 15 mm.
40. The inner distance on the front spring strut (between the mounting tabs) must be 27 mm.   40. The inside distance between the mounting bracket of the front damper must be 27 mm.
41. From chassis number Y-on the 10th. place.   41. from chassis number Y on the 10th position.
42. For vehicles with 50 mm suspension strut.   42. For cars with 50 mm suspension strut.
43. For vehicles with 55 mm suspension strut.   43. For cars with 55 mm suspension strut.
44. For vehicles built between 10.91 and 5.92, the upper support bearings (BMW no.: 31331090467) must be used.   44. For cars built from October 1991 up to May 1992 the upper attachment must be replaced by BMW part number 31.331.090.467.
45. Until 1998 (up to chassis number 8DX199999).   45. up to 1998 models (up to VIN: 8DX199999).
46. Coupling rods 968220, 968221 required for lowering more than 40 mm.   46. Steering rod 968220, 968221 for lowering above 40mm nessecary.
47. After the chassis has been installed, the clearance
the tires to the front suspension strut must be checked (min. 5 mm) and if necessary by means of 
tested spacers to restore.		   47. After mounting the clearance between Wheel and Suspension Strut must be at least 5mm. If it is smaller you have to use wheel spacers.
48. Audi: year of manufacture up to 4.00, VW: year of manufacture up to 9.99.   48. Audi: Model year up to 4.00, VW: Model year up to 9.99.
49. Audi: Year of manufacture from 5.00, VW: Year of manufacture from 10.99.   49. Audi: Model year after 5.00, VW: Model year after 10.99.
50. Without 16V, VA mounting hole spacing 52 mm.   50. Without 16V, front bracket bolt distance 52 mm.
51. Without 16V, VA mounting hole spacing 54 mm.   51. Without 16V, front bracket bolt distance 54 mm.
52. Without Rallye, TD, Genty, CT, CTI, GTI.   52. Without Rallye, TD, Genty, CT, CTI, GTI.
53. Year of manufacture up to 8.04, without 2.0T, 3.0V6 CDTi, without IDS.   53. Model year up to 08.04, without 2.0T, 3.0V6 CDTI, without IDS.
54. From model year 8.04, without 2.0T, 3.0V6 CDTi, without IDS.   54. Model year after 08.04, without 2.0T, 3.0V6 CDTI, without IDS.
55. For vehicles with eye mounting on the rear axle.   55. For models with eye mounting at the rear.
56. For vehicles with fork mounting on the rear axle.   56. For models with fork mounting at the rear.
57. Not for vehicles from model year 2004.   57. Not for models built after 2004
58. Front suspension strut, check the dimensions of the mounting tabs: hole spacing 52 mm; distance 23 mm.   58. On front shock check measurements for the bracket: inside width 23 mm, mounting hole distance 52 mm.
59. Only for vehicles with four-wheel drive (4WD).   59. Only for cars with four wheel drive (4WD).
60. For vehicles with EDC, additional attachments from the vehicle manufacturer are required. VA (also 8 cyl. Engine) BMW Part No.: top mount 31331091709, washer 31331116983, sleeve 31331110196, HA BMW Part No.: support bearing 33521091710, support pot 33521090282, washer 33521092986, protective tube 31331137 932, elastomers 33531091031.   60. Additional OE equipment is needed on cars with EDC. Front (also 8 cyl. Engines) BMW part number: Bearing 31331091709, Washer 31331116983, Dust Cap 31331110196. Rear BMW part number: Bearing 33521091710, 33521090282, Washer 33521092986, Dustseal 31331137 932, Bumpstop 33531091031.
61. Sports damper (included in delivery) in conjunction with standard air spring on the rear axle.   xxx61. The OE air suspension is not removed. A rear sport shock is provided and used with the air suspension.
62. Not for vehicles with electronic damper adjustment.   62. Not for vehicles with electronic damping adjustment.
63. For Allen vehicles built before 2005. 6/92 modified strut mounts must be used. BMW Part No.: strut mount 31336764947, washer 31331116983, sleeve 31331110196.   63. For all cars built before 6/92 the use of different top bearing assembly in the front is required. BMW part number: Bearing 31336764947, Washer 31331116983, Dustseal 31331110196.
64. Without electric. Damping force regulation, without IDS+   64. Without electr. damping force adjustment, without IDS+
65. For vehicles with level control, additional attachments from the vehicle manufacturer are required. Audi part no.: shock absorber bearing 8E0512121E, spring support 8E0512149H, stop buffer 4B0512131Q   65. For cars with self-leveling additional OE parts are required: Audi Part number: Bearing 8E0512121E, Springseat 8E0512149H, Bump stop 4B0512131Q
66. Vehicle-specific connector included   66. Model specific plug&play adapter included
67. Hardness adjustment only on the VA   67. Model specific plug&play adapter available as option
68. Only for vehicles with air suspension   68. Only for cars with air suspension
69. Only for vehicles with ABC chassis   69. Only for cars with ABC suspension
70. From chassis number: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6&74337, USA V6: 4LA21527   70. From VIN: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6&74337, USA V6: 4LA21527
71. only for multi-link rear axle   71. only for Multilink rear suspension
72. only for twist beam rear axle   72. only for twist-beam rear suspension
Parts certificate available. For vehicles with an individual operating permit (EBE), an inspection according to §21 StvZo (individual inspection) is required. Sets without available as export items.   certificate existing. For cars with a single operating permit (EBE) an approval regarding §21 StvZo is required. Sets without can be ordered for export market.
iV In preparation, please inquire.   iV In development, please call.
(…) Notes in brackets only apply to complete chassis.   (…) Remarks in brackets only for kits.
AV Sale.   AV selling off.
  We reserve the right to make technical changes. We assume no liability for printing errors.     Subject to possible technical revisions. Reserves the right to change product specifications. We do not assume liability for misprinting.
         



Customs tariffs and customs duties/import taxes

Some countries charge fees/taxes for importing goods!
Please inquire about these fees before purchasing!

Due to vehicle-specific tolerances a contact between the drive shaft and the anti-roll bar might occur. In such case it is required to install a modified anti-roll bar. For Coilover Sets use Order No. 968 550 000 (Anti-roll bar conversion set without Xenon headlights). For Suspension Kits use a longer steering rod from your VW/Audi dealer. For vehicles with EDC, additional attachments from the vehicle manufacturer are required. VA (also 8 cyl. Engine) BMW Part No.: top mount 31331091709, washer 31331116983, sleeve 31331110196, HA BMW Part No.: support bearing 33521091710, support pot 33521090282, washer 33521092986, protective tube 31331137 932, elastomers 33531091031. Additional OE equipment is needed on cars with EDC. Front (also 8 cyl. Engines) BMW part number: Bearing 31331091709, Wash
Hersteller Vogtland
Herstellernummer 952039