Feature:
1) 2 channels, both are respectively controlled by independent knobes;
2) 150MHZ analog channel bandwidth;
3) 1 GSa/s real-time sample rate;
4) 8M memory depth;
5) Vertical range 2mV/div ~ 10V/div;
6) Vertical resolution : 8bit;
7) Trigger: Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Delay, UART, LIN, CAN, SPI, IIC;
8) CAN decode and protocol analysis: RS232/UART、I2C、SPI、CAN、LIN
9) Can save as multiple data formats, such as setting, waveform, referance waveform, CSV, picture;
10) 5 bits digital voltage meter and 6 bits hardware frequency indicator function;
11) 32 kinds of auto measurements with statistics, real-time statistics of maxmum, minimum, standrad deviation and etc.;
12) 2 sets of digital voltmeter;
13) Support threshold testing, free measurements within the screen;
14) Abundant SCPI remote command control;
15) Many external interface: USB Host/Device
Model | DSO2D15 | DSO2D10 | DSO2C15 | DSO2C10 |
Bandwidth | 150MHz | 100MHz | 150MHz | 100MHz |
Oscilloscope channels | 2CH | 2CH | 2CH | 2CH |
Waveform generator | 1CH | 1CH | - | - |
Oscilloscope | ||||
Sample rate | 1GSa/s (single channel) 500MSa/s (two channels) | |||
Acquisition | ||||
Normal | Sample data | |||
Peak-to-peak value | Display high frequency and random burr | |||
Average | Average waveform, times: 4, 8, 16, 32, 64, 128 | |||
High resolution | Up to 12bit | |||
Input | ||||
Input coupling | DC, AC, GND | |||
Input impedance | 1MΩ±2% ‖20pF±3pF | |||
Probe attenuation factor | 1X, 10X, 100X, 1000X | |||
Voltage rating | 300V CAT II | |||
Maximum input voltage | 300VRMS (10X) | |||
Horizontal | ||||
Waveform interpolation | (sin x)/x | |||
Maximum record length | Single channel maximum 8M | |||
Two channels maximum 4M | ||||
Horizontal scale range | 2ns/div~100s/div 1, 2, 5 step by step | |||
Time base mode | Y-T, X-Y, Roll | |||
Zero offset | ±0.5 div×minimum time base gear | |||
Sample Rate and Delay Time Accuracy | ±25ppm | |||
Delta Time Measurement Accuracy (Full Bandwidth)Sample Rate and Delay Time Accuracy | single-shot, Normal mode ±(1 sample interval+100ppm×reading+0.6ns) | |||
>16 times averages ±(1 sample interval+100ppm×reading+0.4ns) | ||||
Sample interval=sec/div÷200 | ||||
Sample Rate and Delay Time Accuracy | ±50ppm(at any interval greater than 1ms) | |||
Vertical | ||||
Model | DSO2D15 | DSO2D10 | DSO2C15 | DSO2C10 |
Bandwidth | 150MHz | 100MHz | 150MHz | 100MHz |
Rising time in BNC position (typical) | 2.4ns | 3.5ns | 2.4ns | 3.5ns |
Vertical resolution | 8 bits resolution, each channel samples simultaneously | |||
Vertical sensitivity | 2mV/div to 10V/div | |||
Offset range | ≥ 200mV/div, ±1V; | |||
<200mV/div ±50V | ||||
Mathematical operation | +, -, ×, ÷, FFT | |||
FFT | Window: Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop | |||
Bandwidth Limit | 20MHz | |||
Bass response(-3db) | In BNC position ≤ 10Hz | |||
Vertical gain accuracy | In ''normal'' or ''average'' acquisition mode, the accuracy of 10V/div to 10mV/div is ±3%; | |||
In ''normal'' or ''average'' acquisition mode, the accuracy of 5mV/div to 2mV/div is ±4% | ||||
Note: Bandwidth reduced to 6MHz when using a 1X probe | ||||
Trigger | ||||
Trigger type | Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, IIC | |||
Trigger level range | ±5 divisions from the center of the screen | |||
Trigger mode | Auto, Normal, single | |||
Level | CH1~CH2 | ±4 divisions from the center of the screen | ||
EXT | 0~3.3V | |||
Holdoff range | 8ns~10s | |||
Trigger level accuracy | CH1~CH2 | 0.2 div×volts/div within ±4 divisions from the center of the screen | ||
EXT | ±(Set value× 6%+40mV) | |||
Edge trigger | Slope | Rising edge, falling edge, rising or falling edge | ||
Signal source | CH1, CH2, EXT | |||
Pulse width trigger | Polarity | Positive polarity, negative polarity | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1~CH2, | |||
Pulse width range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Video trigger | Signal standard | NTSC, PAL | ||
Signal source | CH1~CH2 | |||
Synchronization | Scanning line, line number, odd field, even field, all field | |||
Slope trigger | Slope | rising, falling | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1 ~ CH2 | |||
Time range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Overtime trigger | Signal source | CH1~CH2, | ||
Polarity | Positive polarity, negative polarity | |||
Time range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Window trigger | Signal source | CH1~CH2 | ||
Pattern trigger | Pattern | 0: low level; 1: high level; X: ignore | ||
Level(signal source) | CH1~CH2 | |||
Interval trigger | Slope | rising, falling | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1~CH2 | |||
Time range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Under Amp trigger | Polarity | Positive polarity, negative polarity | ||
Condition(When) | <, >, !=, = | |||
Signal source | CH1~CH2 | |||
Time range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
UART trigger | Condition(When) | Start, Stop, data, Parity ERR, COM ERR | ||
Signal source(RX/TX) | CH1~CH2 | |||
Data format | Hex (hexadecimal) | |||
Data length | 1 byte | |||
Data bit width | 5 bit, 6 bit, 7 bit, 8 bit | |||
Odd-even check | none, odd, even | |||
Idle level | high, low | |||
Baud rate (optional) | 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s | |||
Baud rate(user-defined) | 300bit/s~334000bit/s | |||
LIN trigger | Condition(When) | Interval field, synchronization field, ID field, synchronization error, identifier, ID and data | ||
Signal source | CH1~CH2 | |||
Data format | Hex (hexadecimal) | |||
Baud rate (optional) | 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s | |||
Baud rate(user-defined) | 300bit/s~334000bit/s | |||
CAN trigger | Condition(When) | Start bit, remote frame ID, data frame ID, frame ID, data frame data, error frame, all errors, ACK Error, overload frame | ||
Signal source | CH1~CH2 | |||
Data format | Hex (hexadecimal) | |||
Baud rate (optional) | 10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000, 1000000 | |||
Baud rate(user-defined) | 5kbit/s~1Mbit/s | |||
SPI trigger | Signal source | CH1~CH2 | ||
Data format | Hex (hexadecimal) | |||
Data bit width | 4, 8, 16, 24, 32 | |||
IIC trigger | Signal source (SDA/SCL) | CH1~CH2 | ||
Data format | Hex (hexadecimal) | |||
Data index | 0~7 | |||
When(condition) | Start bit, stop bit, No Ack, address, restart, address and data | |||
Measurement | ||||
Cursor | Voltage difference between cursors △V | |||
Time difference between cursors △T | ||||
Reciprocal of △T, in Hertz (1/△T) | ||||
Auto measurement | frequency, period, mean, peak-to-peak, RMS, minimum, mixmum, rising time, falling time, + width, - width, base, top, middle, amplitude, overshoot, preshoot, rising edge phase difference, falling edge phase difference, + duty, - duty, period mean, PRMS, FOVshoot, ROVshoot, BWIDTH, FRF, FFR, LRR, LRF, LFR, LFF | |||
DVM | Data source | CH1, CH2 | ||
Measurement type | DC RMS | |||
AC RMS | ||||
DC | ||||
Frequency meter | hardware 6 bits frequency meter | |||
Arbitrary waveform generator | ||||
Channel | 1 | |||
Sample rate | 200MSa/s | |||
Vertical resolution | 12 bits | |||
Maximum frequency | 25 MHz | |||
Standard waveforms | sine, square, ramp,Exp, noise, DC | |||
Arbitrary waveform | Arb1, Arb2, Arb3, Arb4 | |||
Sin | Frequency range | 0.1Hz~25MHz | ||
Square/pulse | Frequency range | 0.1Hz~10MHz | ||
Triangular wave | Frequency range | 0.1Hz~1MHz | ||
Sampling wave | Frequency range | 0.1Hz~1MHz | ||
Index | Frequency range | 0.1Hz~5MHz | ||
Noise | ||||
Arb1 | Frequency range | 0.1 Hz to 10 MHz | ||
Arb2 | Frequency range | 0.1 Hz to 10 MHz | ||
Arb3 | Frequency range | 0.1 Hz to 10 MHz | ||
Arb4 | Frequency range | 0.1 Hz to 10 MHz | ||
Waveform length | 8KSa | |||
Frequency | Accuracy | 100 ppm (<10 kHz) 50 ppm (>10 kHz) | ||
Resolution | 0.1 Hz or 4 bits,take the greater one | |||
Amplitude | Output range | 10mV~7Vp-p (high impedance) | ||
5mV~3.5Vp-p (50Ω) | ||||
DC offset | Range | ±3.5 V, high impedance | ||
±1.75 V, 50 Ω | ||||
Resolution | 100 μV or 3 bits, take the greater one | |||
Accuracy | 2% (1 kHz) | |||
Output impedance | 50 Ω | |||
General specifications | ||||
Display | Display type | 7'' diagonal TFT liquid crystal | ||
Display resolution | 800 (horizontal)*480 (vertical) pixels | |||
Display colour | 16 million colours (24 bits true colour) | |||
Persistence time | minimum, 1 s, 5 s, 10 s, 30 s, infinite | |||
Display type | dot, vector | |||
Display brightness | adjustable | |||
Grid type | adjustable | |||
Grid brightness | adjustable | |||
Interface | Standard interface | USB Host,USB Device | ||
General specifications | Probe compensator output | |||
Output voltage, typical | about 2Vpp input ≥1MΩ load | |||
Frequency, typical | 1kHz | |||
Power supply | 100-120VACRMS(±10%), 45Hzto 440Hz, CATⅡ | |||
120-240VACRMS(±10%), 45Hz to 66Hz, CATⅡ | ||||
Power consumption | <30W | |||
Fuse | T, 3.15A, 250V, 5x20mm | |||
Operating temperature | 0~50 °C (32~122 °F) | |||
Storage temperature | -40~+71 °C (-40~159.8 °F) | |||
Humidity | ≤+104℉(≤+40°C): ≤90% relative humidity | |||
106℉~122℉ (+41°C ~50°C): ≤60% relative humidity | ||||
Altitude | Operating and nonoperating | 3, 000m (10, 000 feet) | ||
Mechanical shock | Random vibration | 0.31 g RMS from 50Hz to 500Hz, | ||
10 minutes on each axis | ||||
Nonoperating | 2.46g RMS from 5Hz to 500Hz, | |||
10 minutes on each axis | ||||
Operating | 50g, 11ms, half-sine wave | |||
Mechanical | Size | 318 x 110 x 150mm (length x width x height) | ||
Weight | 1900g |
We will ship all items within 1-2 working days upon receipt of payment,our goal is: hope you will receive it in short time.
Import duties and taxes are not included in the item price or shipping charges.
These charges are the buyer responsibility.
We will declare customer required value for small taxes .
Warranty&Return Policy:
We encourage all customers to communicate with us through eBay messages.
If you have any questions or comments whatsoever regarding our products or listing, we are waiting to hear from you
A 1 year warranty is offered for this product.If the product malfunctioned under proper usage per instructions
manual within the warranty period, please contact us to obtain shipping instructions and send it back at your shipping costs.
30 days evaluation and investigation takes placed after receiving your return item.A brand new replacement unit will
be sent to you at our shipping costs if it meets our warranty