Great News!  for USA buyers ,Ship from USA warehouse, after payment, within 3-5 days for receiving products! No taxes from customs, no damage, better service, please don't hesitate!
The item includes:

4 PCS Nema 34 stepper motor with 1090oz-in for Single shaft,5.6A

4 PCS DQ860HA Stepper Driver with 80VDC,7.8A, 256 Microstep,

4 PCS 350W,60VDC,5.9A Power supply,

1 PC Breakout Board,

1 PC DB25 Cable.

High Quality Porducts!!!

1, Stepper Motor

Technical Specifications

Part No.:                      85BYGH450D-008 single shaft 

Frame Size:                  NEMA34

Step Angle:                 1.8 degree

Voltage:                       2.13 V

Current:                      5.6 A/phase

Resistance:                 0.35 Ohm/phase

Inductance:                 5.0 mH/phase

Holding torque:            7.7N.m            1090oz-in

Rotor inertia:               1700g-cm2

Number of wire leads: 4

Weight:                          3.6 kg

Length:                         100mm

SHAFT DIAMETER : 14MM with FLATS on the shaft


RED           A+

Green               A-

YELLOW       B+

BLUE             B-


2, Stepper Motor Driver DQ860MA

DQ860HA

 

DQ860HA is a type  of two-phase hybrid stepping motor driver, The drive voltage of which is from 24VDC to 80VDC. It is designed for use with 2-phase hybrid stepper motor of all kinds with 57mm to 86mm outside diameter and less than 7.8A phase current. This circuit that it adopts is smiliar to the circuit of servo control which enables the motor run smoothly almost without noise and vibration. Hording torque when DQ860MA run under high speed is also significantly higher than the other two-phase driver, what’s more, the positioning accuracy is also higher. It is widely used in middle and big size numerical control devices such as curving machine, CNC machine, and computer embroider machine, packing machines and so on.

 
Features:
  •   High performance, low price
  •   Average current control, 2-phase sinusoidal output current drive
  •   Supply voltage from 24VDC to 80VDC
  •   Opto-isolated signal I/O
  •   Overvoltage, under voltage, overcorrect, phase short circuit protection
  •   15 channels subdivision and automatic idle-current reduction
  •   8 channels output phase current setting
  •   Offline command input terminal
  •   Motor torque is related with speed, but not related with step/revolution
  •   High start speed
  •   High hording torque under high speed

◆Low cost and good high-speed

torque

◆14 selectable resolutions

◆Supply voltage up to +80VD               

◆Suitable for-2-phase and 4-phase motors

◆ rated Output current up to 5.6A .peak current for 7.8A

◆Dip switch current setting 8different

values

◆Optically isolated input signals

◆Pulse frequency up to 200KHz  

◆Automatic idle-current reduction

◆Small size  (143*107*37),Weight:0.5KG

 

 

3, Power Supply

350W,60VDC,5.9A 

4, Breakout Board

 

Description:

  • Built in DB25 male connector.
  • DB25 Output Pin:P1,P2,P3,P4,P5,P6,P7,P8,P9,P14,P16,P17.
  • DB25 Input Pin: P10,P11,P12,P13,P15.
  • DB25 GND Pin: P18-P25.
  • Power supply: +5V DC.
  • Built in C-class Optical-coupler.
  • High quality with Surface-mount Tech.

 We ship worldwide!

 

 

                Our Products are mainly used in robotization, Spinning Automatization, Printing, Packing, Medica   Machine, Make-up Equipment, Communication,    Household Appliance, Water Pump, Milling Machine, Engraver Machine, CNC Routers.. etc automatic equipment of various trades.