DC 12V 3A 4 Wire PWM PC CPU Fan Temperature Control Thermostat Speed Controller
Popular
Product Introduction
Feature
1. Using high-quality materials, the quality is guaranteed
2. The appearance of the product is exquisite and small
3. Supports low temperature shutdown of fans within 3A, can directly turn off the fan power, and supports back-sequence fans
4. The product wiring is simple and convenient
5. Support four-wire fan speed regulation
1. Using high-quality materials, the quality is guaranteed
2. The appearance of the product is exquisite and small
3. Supports low temperature shutdown of fans within 3A, can directly turn off the fan power, and supports back-sequence fans
4. The product wiring is simple and convenient
5. Support four-wire fan speed regulation
Specification
Design power supply voltage: DC12V
Voltage range: DC8-16V (circuit operating voltage, please pay attention to the fan voltage range)
Circuit self-consumption: less than 40mA (tested at 12V)
Fan current: no more than 3.3A
PWM range: 1-100 (signal percentage is not actual speed ±0.5%)
PWM frequency: 25KHZ (plus or minus 1KHZ)
PWM signal amplitude: 5V (no load)
Temperature measurement range: -9.9-99.9℃
Temperature measurement error: the error in the range of 0-50°C is lower than 1.2°C, and the error in other ranges is lower than 2°C
Design power supply voltage: DC12V
Voltage range: DC8-16V (circuit operating voltage, please pay attention to the fan voltage range)
Circuit self-consumption: less than 40mA (tested at 12V)
Fan current: no more than 3.3A
PWM range: 1-100 (signal percentage is not actual speed ±0.5%)
PWM frequency: 25KHZ (plus or minus 1KHZ)
PWM signal amplitude: 5V (no load)
Temperature measurement range: -9.9-99.9℃
Temperature measurement error: the error in the range of 0-50°C is lower than 1.2°C, and the error in other ranges is lower than 2°C
Precautions
1. This control only controls the speed adjustment of the fan controlled by the four-wire standard PWM signal. The signal specification is 25KHZ 5V. Conventional chassis, CPU and many server four-wire fans support it, but it cannot control the speed regulation of 2-3 wire fans!
2. The difference between the acceleration temperature and the full speed temperature should not be lower than 5°C, and the difference between the shutdown temperature and the acceleration temperature should not be lower than 2°C. When modifying the parameters, if the value breaks the above temperature difference, the program will automatically adjust the other two parameters.
1. This control only controls the speed adjustment of the fan controlled by the four-wire standard PWM signal. The signal specification is 25KHZ 5V. Conventional chassis, CPU and many server four-wire fans support it, but it cannot control the speed regulation of 2-3 wire fans!
2. The difference between the acceleration temperature and the full speed temperature should not be lower than 5°C, and the difference between the shutdown temperature and the acceleration temperature should not be lower than 2°C. When modifying the parameters, if the value breaks the above temperature difference, the program will automatically adjust the other two parameters.
Show description
Three-digit digital tube: display specific parameters and values
LED "×10 RPM": Speed unit light This light is on and the digital tube displays the fan speed. The value is the value after dividing the speed by 10. For example, if 256 is displayed, the actual fan speed is 2560RPM (revolution/min)
LED "℃": temperature unit light, this light is on and the digital tube displays the temperature measured by the current probe
LED "RUN": Fan running indicator light on when the fan is running and off when the fan is off
Three-digit digital tube: display specific parameters and values
LED "×10 RPM": Speed unit light This light is on and the digital tube displays the fan speed. The value is the value after dividing the speed by 10. For example, if 256 is displayed, the actual fan speed is 2560RPM (revolution/min)
LED "℃": temperature unit light, this light is on and the digital tube displays the temperature measured by the current probe
LED "RUN": Fan running indicator light on when the fan is running and off when the fan is off
List
1 x Module
1 x Sensing wire
1 x Module
1 x Sensing wire
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
DC 12V 3A 4 Wire PWM PC CPU Fan Temperature Control Thermostat Speed Controller
Product Introduction
Feature
1. Using high-quality materials, the quality is guaranteed
2. The appearance of the product is exquisite and small
3. Supports low temperature shutdown of fans within 3A, can directly turn off the fan power, and supports back-sequence fans
4. The product wiring is simple and convenient
5. Support four-wire fan speed regulation
1. Using high-quality materials, the quality is guaranteed
2. The appearance of the product is exquisite and small
3. Supports low temperature shutdown of fans within 3A, can directly turn off the fan power, and supports back-sequence fans
4. The product wiring is simple and convenient
5. Support four-wire fan speed regulation
Specification
Design power supply voltage: DC12V
Voltage range: DC8-16V (circuit operating voltage, please pay attention to the fan voltage range)
Circuit self-consumption: less than 40mA (tested at 12V)
Fan current: no more than 3.3A
PWM range: 1-100 (signal percentage is not actual speed ±0.5%)
PWM frequency: 25KHZ (plus or minus 1KHZ)
PWM signal amplitude: 5V (no load)
Temperature measurement range: -9.9-99.9℃
Temperature measurement error: the error in the range of 0-50°C is lower than 1.2°C, and the error in other ranges is lower than 2°C
Design power supply voltage: DC12V
Voltage range: DC8-16V (circuit operating voltage, please pay attention to the fan voltage range)
Circuit self-consumption: less than 40mA (tested at 12V)
Fan current: no more than 3.3A
PWM range: 1-100 (signal percentage is not actual speed ±0.5%)
PWM frequency: 25KHZ (plus or minus 1KHZ)
PWM signal amplitude: 5V (no load)
Temperature measurement range: -9.9-99.9℃
Temperature measurement error: the error in the range of 0-50°C is lower than 1.2°C, and the error in other ranges is lower than 2°C
Precautions
1. This control only controls the speed adjustment of the fan controlled by the four-wire standard PWM signal. The signal specification is 25KHZ 5V. Conventional chassis, CPU and many server four-wire fans support it, but it cannot control the speed regulation of 2-3 wire fans!
2. The difference between the acceleration temperature and the full speed temperature should not be lower than 5°C, and the difference between the shutdown temperature and the acceleration temperature should not be lower than 2°C. When modifying the parameters, if the value breaks the above temperature difference, the program will automatically adjust the other two parameters.
1. This control only controls the speed adjustment of the fan controlled by the four-wire standard PWM signal. The signal specification is 25KHZ 5V. Conventional chassis, CPU and many server four-wire fans support it, but it cannot control the speed regulation of 2-3 wire fans!
2. The difference between the acceleration temperature and the full speed temperature should not be lower than 5°C, and the difference between the shutdown temperature and the acceleration temperature should not be lower than 2°C. When modifying the parameters, if the value breaks the above temperature difference, the program will automatically adjust the other two parameters.
Show description
Three-digit digital tube: display specific parameters and values
LED "×10 RPM": Speed unit light This light is on and the digital tube displays the fan speed. The value is the value after dividing the speed by 10. For example, if 256 is displayed, the actual fan speed is 2560RPM (revolution/min)
LED "℃": temperature unit light, this light is on and the digital tube displays the temperature measured by the current probe
LED "RUN": Fan running indicator light on when the fan is running and off when the fan is off
Three-digit digital tube: display specific parameters and values
LED "×10 RPM": Speed unit light This light is on and the digital tube displays the fan speed. The value is the value after dividing the speed by 10. For example, if 256 is displayed, the actual fan speed is 2560RPM (revolution/min)
LED "℃": temperature unit light, this light is on and the digital tube displays the temperature measured by the current probe
LED "RUN": Fan running indicator light on when the fan is running and off when the fan is off
List
1 x Module
1 x Sensing wire
1 x Module
1 x Sensing wire
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.