TRIMMER on PCB-NEW-[TRMHV10W]-5~12Vin-(150V~200V)out Adjustable HIGH VOLTAGE SUPPLY MODULE for NIXIE TUBE ERA
This is the HV10W Adjustable with trimmer on PCB-HV PUS Module,which you can adjust the out voltage by yourself.
For 5V in,can drive 6pcs in-14 clock with no problem,
THIS
MODULE CONTAINS DANGEROUS, HIGH VOLTAGE POTENTIALS. USE CAUTION.
DO NOT TOUCH ANY PART OF THE MODULE WHEN IT IS WORKING.
Tips:
1.Module contains a Trimmer on PCB to adjust the output
voltage in range ~150V~200V(when no loads be connected on the output side, the output voltage will be ~+155V~+205V high,it is normal);
2. DIP version in Standard 0.1"(2.54mm) pins(SMD version in STD 0.1" gap too), easy to be used, can use bread board or Round
DuPont-Wires etc.
3. Module contains input reverse polarity protection+over current protection+soft
boot-up. When over heat, the module will turn off, you need to re-power on to
reset the module;
4. We
recommend working in 12V in (Can work under 5V in,but output much lower hv current when 5V in);
5. If one module's power is not suited for your app,use two or more modules for
driving the separated tube(s),etc.;
6. Do not connect the modules'
outputs in "Parallel Connection"!!!
Description(For reference only):
TRMHV10W. is a newly designed high voltage module, it works
under 5V~12V in,
with ~150V~200V DC max output,and the output voltage is adjustable by a trimmer on PCB.
Have tested
under 5V in,can do:
Light up 6pcs IN-18 NIXIE tubes(+4pcs NE-2 neon lamps as middle colon for NIXIE clock) or 12PCS IN-14 tubes with 4pcs NE-2 neon lamps with no problem(~165V output);
Have tested
under 12V in:
Can output 170V with 50mA current in ~82% eff.
Can use it for driving vacuum amp tube(usually need ~200V output);It
contains an Trimmer on PCB to adjust the output
Module Size : please check pics;
Module Pins : 0.1"/100mil/2.54mm std. pins gap between pins or smd-pads;
PCB Color : Black;
Freq: ~85kHz;
Pin Functions
ID |
Name |
Description |
0 |
EN |
Enable pin for turning the module ON/OFF(Not Optional,1 to on; 0(GND) to off) |
1 |
Vcc/+5V |
Input
supply voltage, 4.5V to 15V. Tips:have tested,can be drivered by using Li-poly battery. |
2 |
GND |
Ground |
3 |
HV |
High voltage output. Min +150V; Max:+200V(+-5%) |
4 |
GND |
Ground |
*EN pin can be controlled by 3.3V/5V MCU GPIO directly,not need to add extra resistor or add 1~10k resistor in serial depends on u.
For 24*7 continually working condition, we recommend you control the input current less than 1000mA when 12V in, it keeps this module working under the low heat condition.
And
this module is suiteble for driving over 12pcs of IN-18 nixie tubes (12Vin&~170V out) with no problem.
Typical Usage:
For driving vacuum Tubes or other purposes
need high voltage;
Note:
We may not be able to provide extra
technology support!
We may will change the Outlook/Circuit/PCB/Components etc. without
notification!
It's DIY stuff, may need 3~5 working days for assembling and heat
testing!
Contains:
1PCS TRMHV10W module only,please left a note for the module type and quantity info,
ready to go.(without any tubes, without power adapter,
without wires;)
In default we send u DIP version of the module,if need SMD version(no pins with half hold pad on the edge of PCB),please left a note.
For Module Type,please left a note or send us meassge via ebay,or we will send module TYPE -E in default.
All DIP modules will contain a few feamle socket pins for u easy to install,all PCB install layout of modules please check the last item pic as reference. (For DIP moudles we recomment be installed via female socket pins,but if wanna solder the DIP module directly on PCB,recommend use ~1.2~1.4mm pad with ~0.8mm middle hole,and solder pins fast.)
Payment methods:
We ONLY accept PayPal on eBay selling, other payment is
not acceptable.
Please PAY within 7 days, or we'll re-selling the item.
Shipping:
We ship to American via ePacket Delivery with tracking number;
We ship to Other countries/locations via International Economy Package with tracking number;
For shipping to The United Kingdom or Canada or Australia
or Russian Federation, we strongly recommend you update to the EUB(express);
Price for updating to the EUB(express):
For shipping to The United Kingdom or Australia: +5.99usd;
For shipping to Russian Federation: +3.99usd;
Shipping time:
10-20 working days for ePacket Delivery to the U.S.A.(normally you will receive it in about two weeks),
depends on the destination location; For other far locations may need more
days.
Please note that International Economy
Package can ship to the World wild with low price, but the transport speed is very unstable, mail delay is
very normal, shipping to far locations may cost
over 30 days, sometimes the cargoes will be stacked in the airport for over one month(especially in the special meeting
time, it happened before).
Please understand that we can't control the mail
speed. If the mail delayed, please be patient.
If you want to save your time, add extra money for
updating to the EMS.
We ship to your PAYPAL Verified Address only;
Any import tax or charges should be paid by the
buyer.