Please confirm that the rated current of your motor is less than 5A before ordering.
Parameters:
1.the input power supply (VAC): AC180-260V 50/60Hz (for global voltage)
2.the output armature voltage range (VDC): DC180V
3.the
output armature current range (A): 8A (0.1A-10A can be arbitrarily
set) If the current is too big need to increase the heat
4.the output excitation voltage range (VDC): 100/200 (default full-bridge rectifier, which is 0.9 times the input voltage)
5.the output excitation current range (A): 1A
6.the working frequency: 16 KHz
7.given signal mode (V / mA): default potentiometer, 0-5V, 0-10V, 4-20mA, PWM, touchtone
8.enable control mode (EN): switch
9.soft start (acceleration time adjustment range) (S): 0-10S (default 2 seconds)
10.soft stop (deceleration time adjustment range) (S): 0-10S (default 2 seconds)
11.double loop PI regulation (voltage and current) control is more reliable
12.IR torque compensation range: 0-100% (default 0)
13.overcurrent range: 0 setpoint (default 8A)
14.overcurrent mode: stop output and indication (display code E1)
15.short-circuit protection: stop output and indication (display code E0)
16.overheat protection: power tube temperature exceeds 100 ° off the output and the indication (display code E2)
17.built-in digital display module can display real-time operating voltage with current
18.Dimensions: Length 140mm × 98mm × height 38mm width
19.Connection: terminal type (convenient)
Advantages:
1.using pulse technology to speed more stable, low speed forceful
2.with a short circuit, overcurrent, overtemperature protection cutoff device to make more reliable performance
3.with the elimination of soft starter motor starting current is too large
4.high and low voltage signal is completely isolated, the use of safer
Precautions:
1,
the governor closed the input power, Touched by hand within a minute
ban high-voltage terminal, There are high-voltage capacitors, To prevent
electric shock!!!
2,
for the two lines of DC permanent magnet motor, Two lead wires
connected directly to the armature M + with M-. Prohibit access
exciting!
PWM signal requirements:
1, the default PWM signal level is 5V, the signal frequency 1KHZ above, with a load capacity of more than 0.5MA.
*5V level without resistors in series with PWM input port,
*10V PWM level from 0-10V input port or serial port 10K resistor in the PWM input,
*12V level 3.9K resistor string from 0-10V input port or serial port 13.7K PWM input resistors,
*24V level string 27K resistor from 0-10V input port or serial port 16.8K resistor PWM input
Package: 1x DC Motor Speed Controller
Payment Method: PayPal preferred
Shippment:
International shipping requires complicated shipping procedures (such as both countries customs, transit stations etc.), also will be affected by many factors, such as holidays, weather conditions etc, If you have not received your shipment after long time days from payment, please contact us.
Returns & Replacements & Repair
We accept returns & replacements within 14 days from the day the customer receive the products, please make first contact within 14 days from receiving the order. Products should be returned in original condition. As a benefit to our customers, we also provide repair within 3 months from the day when this item is shipped out, after repair is done, we will send you the item, but the customer should pay both shipping ways.
Shippment:
International shipping requires complicated shipping procedures (such as both countries customs, transit stations etc.), also will be affected by many factors, such as holidays, weather conditions etc, If you have not received your shipment after long time days from payment, please contact us.
Returns & Replacements & Repair
We accept returns & replacements within 14 days from the day the customer receive the products, please make first contact within 14 days from receiving the order. Products should be returned in original condition. As a benefit to our customers, we also provide repair within 3 months from the day when this item is shipped out, after repair is done, we will send you the item, but the customer should pay both shipping ways.
