modname=ckeditor

One Use and One Standby Water Pump Intelligent Controller, Two Kinds of Signal Exchange, Manual and Automatic Integration

 

Model 1: Float or pressure gauge signal

 
Model 2: Electrode signal

 

Preface：

        Welcome to use sewage pump for general useController！ In order to give full play to the performance of this product and ensure the safety of users and equipment，Before use，Please read this manual in detail。 This product manual is a random attachment，Please keep it properly after use.，In case of future overhaul and maintenance of the pump intelligent controller。Attention：The function of this controller is compiled according to the requirements of some customers.，Please read the function introduction carefully.，Is it appropriate for the current project needs。 If you have other requirements，Please feel free to contact our offices or distributors in various places.，You can also contact the after-sales service center of the company's headquarters directly.，We will serve you wholeheartedly.。Product upgrade or manual content changes，Without notice。

Product Overview：

     YZZN-D103STypeIntelligent water pump universalController，It is mainly used for drainage、Intelligent control of water feeding equipment，Adapt 22KW The following，Direct start。


Main functions：

  1. One for use and one for preparation、Fault mutual investment、Overload mutual investment、Load increase and load decrease；
  2. Support float control/Pressure control（Key switch）；
  3. Automatic interface with hand；
  4. With overload feedback protection function；Remote control function；
  5. The contact connected with overload feedback can be normally opened.、Normally closed free switching；
  6. Main pump selection function：It can be started by a single pump，Can also rotate freely；
  7. Timing inspection function；

Overall dimensions：

Controller installation size：164mmX102mmX50mm   ABSNew material

Optimal opening size：156mm*92mm

Function description：

 

One、In the automatic state：

  1. Overload signal(Passive signal）：“Public”For the public end，AWhen the pump is overloaded，Public and“Overload signalAPump”Closed；BWhen the pump is overloaded，Public and“Overload signalBPump”Closed。（Long press“BPump operation” Button，Freely switchable contact properties：Normally closed or normally open）。
  2. Remote control signal (Passive signal）：Remote control signal connection12Terminal number，In automatic and manual states，Priority startup，12Number terminal and13Terminal number（Public）Short Circuit，Start a pump，Disconnect stop，Short circuit again，Start another pump，Run rotation。
  3. External signal（Passive signal）Input：Can be matched2Floating ball water level point，Or pressure point（Electric contact pressure gauge）。（Long press“BPump stop” Button，Can freely switch floating ball state or pressure state）。
  4. Long press“Main pump selection”PressKey（3More than seconds）Can chooseAPump orBPump as main pump(APumps andBPump switching，Press the key for a short time)，SelectAWhen the pump is the main pump，BPump not working，“APump priority”Indicator light；SelectBWhen the pump is used as the main pump，APump not working,“BPump priority”Indicator light。“APump priority”And“BPump priority”When the indicator light flashes，For rotation status，APumps andBThe pump can be switched to work.。
  5. Timing inspection function：This controller belt240Hour automatic inspection function，Prevent the water pump from rust, corrosion and sticking due to long-term non-operation.，Affect normal use，Press“APump stop”Key can turn off and turn on the timing inspection function。

 

Two、In the manual state：

      The controller panel has“Automatic/Manual”Toggle button，The default state is automatic when power is on.（“Automatic”Indicator light），The controller will run automatically after power-on.，Long press“Automatic/Manual”Button，Switch to manual state（“Manual”Indicator light，At the same time“Automatic”Indicator light is off）；According to the corresponding on the panel“Run”Press the button to start the corresponding pump，Press“Stop”Press the button to stop the corresponding pump（Invalid in automatic state)，Double pumps can be started at the same time。

 

Three、 Introduction of some functions of controller：  

     

1、There are two kinds of automatic signals for the controller.：1Floating ball access type（Electrode access type，Optional）；2Pressure access type。When the controller is powered on，The indicator light flashes in the automatic state.，Then long bright，The controller is a floating ball access type；The indicator light flashes twice in the automatic state.，Then long bright，The controller is pressure access type。Long press“BPump stop”Keys can be switched freely。When it is a floating ball access type：Water level and high water level in corresponding automatic signals。When the water level reaches the middle water level，APump start-up operation，When the water level leaves the middle water level，APump stops running；When the water level reaches the middle water level again，BPump start-up operation，Repeated alternating operation，Realize one use, one standby function。When the water level reaches a high water level，Start-up operation of standby pump（At this time，Two pumps run simultaneously），At the same time, the alarm indicator is on，When the water level leaves the high water level，After the start of the pump to stop running，Work so repeatedly and alternately，Realize the function of increasing and decreasing load。Independent operation of medium water level and high water level（That is, start a pump at the middle water level，High water level start two pumps）。

         

2、When the automatic signal of the controller is the access type of electric contact pressure gauge：Corresponding automatic signal For low-end and high-end（Public is the moving end）。Moving end and low end closure，APump operation；Moving end and high end closure，APump stops running。When running the pump，Overload of running pump，Automatic switch to standby pump，Alarm indicator light。Realize one use and one standby，Fault mutual investment。

       

3、“Overload signalAPump”And“Public”ConnectAFeedback overload signal of pump output，Such：ANormally closed contact of pump thermal relay(Long press“BPump operation”Button，Freely switchable contact properties：Normally closed or normally open）；Overload signalBPump”And“Public”ConnectBFeedback overload signal of pump output，Such：BNormally closed contact of pump thermal relay(Can also be changed into a normally open contact，Contact us long press“BPump operation” Button，Freely switchable contact properties：Normally closed or normally open）。

     

4、All signal input points can be madeDC24VInput（Custom，Contact dealer）。

     

5、Controller with memory function，After the function is reset，Restart after power failure，Maintain last feature selection。

     

6、Controller with emergency start function：In case of emergency，Dial the dial switch on the back of the controller body”Emergency“，APump is running。