DESCRIPTION CW TONE GENERATOR KIT
This CW Gen can be used as a Morse Code Practice Oscillator and as well as as CW generator for SSB transceivers like Bitx and others.CW can be used in two ways. 1. By feeding the 700 hertz tone, to the mike input stage of TX.
2. By unbalancing the carrier by a positive voltage from this Generator, which unbalances the balanced modulator.Using As a Morse Morse_Code Practice oscillator.The generator has a side tone oscillator, from which the keying can be monitored. An 8 ohms speaker can be connected to monitor sending of CW.1. Controls: The following controls are available on board.2.Audio Control: Control the audios gain of the side tone oscillator 3. Tone Control: Control the audio tone gains for the microphone TX input stage.4. Carrier Balance: Provides a positive voltage to unbalance the modulator stage in TX for CW5. Delay: Adjust delay for keying CW as per speed required.
The generator can be powered by 12 volts from the TCVR connected to with the 5 pins PC connector or by a 9 Volt battery. An On/Off switch facility is also provided on the board.The CW generator board can also be fitted in the transceiver or transmitter case, the 10K trimmers should be used for this, the 5 PIN PC connector and the RCA connector can be discarded and wires soldered direct on the pads.For using CW there are two methods, which can be used.
1. By feeding the Audio tone 700 Hertz from Tone Control Output point,to the SSB transceiver.2. By providing positive voltage from point Carrier Balance, the voltage is fedto the TX Balanced Modulator stage to unbalance the carrier .Power Source:The unit can be powered by 9 Volt external battery or with 12 Volts from the transceiver being used. The voltage from the tcvr comes through one of the pins of the 5 pin PC Connector on board.A OFF/ON switch can be used when using the 9 volts battery or a jumper can be placed across the switch pads to power it direct.Connecting to Bitx.The unit can be connected to Bitx with the 5 PIN connector of the cw gen and the 4 PIN XLR connector of Bitx with a shielded cable provided. The CW gen can be used externally as well as housed inside the tcvr.COMPONENT VALUE QUANTITYRESISTORS 1/4 WATT 10E 2 RESISTORS 1/4 WATT 18K 2 RESISTORS 1/4 WATT 10K 2 RESISTORS 1/4 WATT 2K2 5 RESISTORS 1/4 WATT 3K3 2 RESISTORS 1/4 WATT 4K7 1 LINEAR POTENTIOMETER 10K 4 DIODE IN4007 3 CAPACITOR DISC 0.01UF 9 ELECRTOLYTIC CAP 47UF 1 ELECRTOLYTIC CAP 100UF 25V 2 ELECRTOLYTIC CAP 3.3UF 63V 1 ELECRTOLYTIC CAP 1uf 63v 1 I.C.BASE 8 PIN 1 I.C.LM386 LM386 1 TRANSISTOR BC557 2 TRANSISTOR 2N3904 3 CONNECTORS WIRE 2 PIN 2 JUMPERS JUMPER 0 OHMS 45-Pin DIN Male Keyboard socket 5 PIN 1 Plastic cover CONNECTOR RCA RCA FOR KEY 1 PRINTED CIRCUIT BOARD CW GENERATOR 1 SHIELDED WIRE 3 CORE 1.7 INCH 1 Battery Clip Wire 1 Speaker 8 ohms 1 Trimmer Presets 10k 4CW Gen PCB 1
_______________________________________________________________________
Buy with confidence from a trusted seller - see my
About me Page
Don't forget to look at
My Other Items
Terms and Conditions.
- Once a bid has been placed, it is a legally binding contract of purchase
- Payment must be received within 4 working days of purchase, however if this is not possible, please let us know to discuss solutions.
- If payment is not received within 7 days of purchase then a Non Paying Buyer Dispute will be filed, and 10 days later a final fee credit lodged
- You will be notified on the day that your goods have been despatched via e-mail
- Once you receive your goods, please inspect them for any damage during transit, and report the said damage within 24hrs via e-mail. If all is well please leave feedback, so we are aware that you have received your goods. Please note that if there are any problems, contact us first via e-mail giving full details of any problem along with your user ID
|
- 7 days after we have dispatched your order, if we have not been notified by you of any problem, or received feedback, we will send a feedback reminder.
- It is the customers responsibility to ensure that payment is received in the due time as listed above
- If paying via Postal Orders, please make them payable to :
- All goods are sent either via DHL Express Or Deutsche Post l second class post (up to 2kg) or Parcelforce 48 (over 2 kg). Shipping as per listing.
- Goods will be dispatched within 48 hrs of cleared fund, subject to the conditions listed in the payment section above.
- We accept no responsibility for goods delayed due to the services of Deutsche Post or DHL
|
Shipping Information
1. International Economy Shipping With Aramex
We do not take any responsibility of any taxes or custom charged in your country. Kindly do the needful of checking duties before you place an order,for there would be no refunds for any duties or taxes charged by your local govt.
|
Payments done through Payoneer
|