Car Battery Relocation Kit With Bolt-On Remote Mount Box

As featured on our 1952 Chevy Pickup for Classic Truck’s Week to Wicked. Watch the transformation !

Kit Includes:

• (1) Custom Bolt-On Remote Mount Car Battery Relocation Box/Steel Tray
• (1) Red Welding Cable - Battery Cable, 10 Foot, 2 gauge
• (1) Black Welding Cable - Battery Cable, 10 Foot, 2 gauge
• (1) Taylor 21405 Top Post Battery Cable Terminal End Kit, 2 Pack
• (1) Taylor 21409 Side Post Battery Cable Terminal End Kit, 3/8 Inch Hole
• (1) Black Battery Terminal Protector Cover
• (1) Red Battery Terminal Protector Cover

Custom Bolt-On Remote Mount Car Battery Relocation Box/Steel Tray

• Relocate the battery from tight locations to where you have more room with a secure and economical weld-in solution
• Simple bolt-in design requires no welding
• Perfect for street applications where under-the-hood or trunk locations may have limited space
• Race applications allow relocating the battery for ideal weight distribution
• 12-gauge steel brackets and 14-gauge steel baseplate holds the weight of your battery
• Six pre-cut holes in each bracket allow battery to be mounted at the right height
• Baseplate is drilled to reduce weight while maintaining strength
• Zinc-plated finish resists corrosion and is ready to mount without having to paint or powder coat first
• Battery box will fit up to a 10.63” long x 7.06” wide battery, up to 7.5” tall
• Includes hold-down angle bar, zinc-plated J-bolts, washers and nylock nuts to keep battery held down tight
• Overall dimensions: 14.38”L x 7.25”W x 6.5”H
• No welding required!

Red Welding Cable - Battery Cable, 10 Foot, 2 gauge

• Welding cable has always been preferred by chassis builders to use for battery cables
• This welding cable is made with very fine copper wire and insulated with synthetic rubber
• This welding cable is more flexible than a battery cable, especially in cold temperatures and it is easier to route into tight spaces
• 2 gauge
• 10 foot
• Red
• 100% copper cable for maximum conductivity

Black Welding Cable - Battery Cable, 10 Foot, 2 gauge

• Welding cable has always been preferred by chassis builders to use for battery cables
• This welding cable is made with very fine copper wire and insulated with synthetic rubber
• This welding cable is more flexible than a battery cable, especially in cold temperatures and it is easier to route into tight spaces
• 2 gauge
• 10 foot
• Black
• 100% copper cable for maximum conductivity

Taylor 21405 Top Post Battery Cable Terminal End Kit, 2 Pack

• Tin plated copper terminals
• Cadium-plated for corrosion resistance
• Designed for a fast and easy install
• Simply strip your battery cable and apply these fittings to the cable and screw into your battery terminal
• For 2 gauge wire
  
• 2 per pack

Taylor 21409 Side Post Battery Cable Terminal End Kit, 3/8 Inch Hole

• Tin plated copper eyelet terminals
• Cadium-plated for corrosion resistance
• Designed for a fast and easy install
• Simply strip your battery cable and apply these fittings to the cable and screw into your battery terminal
• For 2 gauge wire
  
• 2 per pack

Battery Terminal Protector Covers

• Black and Red battery terminal protectors
• Improve the appearance of your battery connections
• Protect against corrosion and shorting
• Overall Length 3.25" x Width 1.63" x Height 0.88"
• 1" tall from base to beginning of taper
• Wire inlet is 3/4" long with a 5/8" inside diameter

Battery Tray:

1. Fits batteries measuring 10.63” long x 7.06” wide, with a height up to 7.5”
2. Works with most batteries in the following groups: 42, 47, 90, 96R, and 97R