L-style Aluminium Bracket: To improving the connection and measurement efficiency and saving the cost on installations, Sure Electronics provides a L-type aluminium bracket for audio amplifier boards. The aluminium bracket supports vertical and horizontal installtion ways to satisfy different installation requirements. With 4 M3 screw lock standoffs and 2 M3 pre-drilled mounting holes, audio amplifier boards could be installed on the bracket easily.
L-style Aluminium Bracket does not include the amplifier board.
The following amplifier board is suitable for the L-style Aluminium Bracket ,you can buy the version in model.
1 x 100Watt Class D Audio Amplifier Board Compact -TPA3116 Electrical Specifications: Specifications typical @ +25℃, Powered by 21V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Power Supply | - | 10 | 21 | 24 | VDC | Idle Power | SD Floating | - | 1.1 | - | W | Standby Power | SD Connected to GND | - | 0.07 | - | W | Maximum Current | 100W @ 2Ohm | - | 5.3 | - | A | Efficiency | 100W @ 2Ohm | - | 89 | - | % | Minimum Load Impedance | - | - | 1.6 | - | Ω | Switching Frequency | SD Floating | - | 398 | - | KHz |
Audio Performance: Specifications typical @ +25℃, Powered by 21V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Gain | - | - | 26 | - | dB | Input Sensitivity(RMS) | @2Ω, 100W, 1KHz | - | 0.83 | - | V | Input Impedance | - | - | 30 | - | KΩ | Output Power | @2Ω THD+N 1% | - | 87 | - | W | @2Ω THD+N 10% | - | 100 | - | W | Bandwidth @ ±3dB | @2Ω | 20 | - | 20K | Hz | THD | @2Ω, 1W, 1KHz | - | 0.05 | - | % | @2Ω, 10W, 1KHz | - | 0.07 | - | % | Output Noise Level | A-weighting,Input Connected to GND | - | 109 | - | µV | SNR | 87W @2Ω THD+N 1% | - | 99 | - | dB
|
2 x 15Watt @ 8ohm Class-D Audio Amplifier Board -TPA3110
Electrical Specification: Specifications typical @ +25℃, Powered by 16V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Power Supply | - | 10 | 16 | 24 | VDC | Idle Power | SD Floating | - | 0.16 | 0.3 | W | Standby Power | SD Connected to GND, FAN OFF | - | 0.006 | 0.1 | W | Maximum Current | 30W @ 6Ohm | - | 2.2 | - | A | Efficiency | 15W @ 6Ohm | - | 87.2 | - | % | Minimum Load Impedance | - | - | 4.8 | - | Ω | Switching Frequency | SD Floating | - | 315 | - | KHz |
Audio Specification: Specifications typical @ +25℃, Powered by 16V DC, unless otherwise noted. Specifications subject to change without notice.
Parameter | Conditions | Min. | Typ. | Max. | Units | Gain | - | 24 | 25 | 26 | dB | Input Sensitivity(RMS) | @6Ω, 15W, 1KHz | - | 589 | - | mV | Input Impedance | - | - | 22 | - | KΩ | Output Power | @6Ω THD+N 1% | - | 10 | - | W | @6Ω THD+N 10% | - | 15 | - | W | Bandwidth @ ±3dB | @6Ω | 20 | - | 20K | Hz | THD | @6Ω, 1W, 1KHz | - | 0.0257 | - | % | @6Ω, 10W, 1KHz | - | 0.36 | - | % | Output Noise Level | A-weighting, Input Connected to GND | - | 114.8 | - | µV | SNR | 10W @6Ω THD+N 1% | - | 94.4 | - | dB |
2 x 15 Watt 4 Ohm Class D Audio Amplifier Board - TA2024
Electrical Specification: Specifications typical @ +25℃, Powered by 12V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Power Supply | - | - | 12 | - | VDC | Idle Power | SD Floating | - | 0.7 | 1.5 | W | Standby Power | SD Connected to GND | - | 0.08 | 0.5 | W | Maximum Current | 30W @ 4Ohm | - | 3.03 | - | A | Efficiency | 15W @ 4Ohm | 80 | - | 85 | % | Minimum Load Impedance | - | - | 4 | - | Ω | Switching Frequency | SD Floating | - | 850 | - | KHz |
Audio Specification: Specifications typical @ +25℃, Powered by 12V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Gain | - | 20 | 21 | 22 | dB | Input Sensitivity(RMS) | @4Ω, 15W,1KHz | - | 748 | - | mV | Input Impedance | - | - | 22 | - | KΩ | Output Power | @4Ω THD+N 1% | - | 10 | - | W | @4Ω THD+N 10% | - | 15 | - | W | Bandwidth @ ±3dB | @4Ω | 20 | - | 20K | Hz | THD | @4Ω, 1W, 1KHz | - | 0.024 | - | % | @4Ω, 10W, 1KHz | - | 0.54 | - | % | Output Noise Level | A-weighting,Input Connected to GND | - | 122.65 | - | µV | SNR | 10W @4Ω THD+N 1% | - | 84.4 | - | dB |
2 x 25 Watt 6 Ohm Class D Audio Amplifier Board - TDA7492
Specification: Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of ST’s TDA7492 chip. TA = 25 °C, fIN = 1 kHz sine wave, RL= 8Ω, VCC = 25V. (Unless otherwise stated) Parameter | Conditions | Min | Typ | Max | Supply Voltage (V) | AA-AB32165 | 14 | 16 | 19 | Quiescent Current (mA) | FAN ON,STBY Disable | - | 90 | - | FAN ON,STBY Enable | - | 50 | - | FAN OFF,STBY Disable | - | 40 | | FAN OFF,STBY Enable | | 10 | | Input Sensitivity (mV) | 21.6dB | - | 257 | - | 27.6dB | 258 | 31.1dB | 258 | 33.6dB | 258 | Input Impedance (Kohm) | - | 48 | 60 | - | Gain (dB) | GAIN0 = L, GAIN1 = L | 20.6 | 21.6 | 22.6 | GAIN0 = L, GAIN1 = H | 26.6 | 27.6 | 28.6 | GAIN0 = H, GAIN1 = L | 30.1 | 31.1 | 32.1 | GAIN0 = H, GAIN1 = H | 32.6 | 33.6 | 34.6 | Output Power (W rms) | RL= 6Ω, THD = 10%, VCC = 25V | - | 25 | - | Efficiency (%) | Both channels output rating power. | - | >90 | - | Minimum Load (ohm) | - | - | 6 | - | Frequency Response (dB) | ±3dB | 20 | - | 22k | Operating Temperature (℃) | - | 0 | 20 | 50 |
2 x 50 Watt 6 Ohm Class D Audio Amplifier Board - TPA3116
Electrical Specification: Specifications typical @ +25℃, Powered by 21V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Power Supply | - | 10 | 21 | 24 | VDC | Idle Power | SD Floating | - | 1.3 | 2.5 | W | Standby Power | SD Connected to GND | - | 0.1 | 0.3 | W | Maximum Current | 100W @ 4Ohm | - | 5.29 | - | A | Efficiency | 50W @ 4Ohm | 87 | - | 92 | % | Minimum Load Impedance | - | 3.2 | - | - | Ω | Switching Frequency | SD Floating | - | 394 | - | KHz |
Audio Specification: Specifications typical @ +25℃, Powered by 21V DC, unless otherwise noted. Specifications subject to change without notice. Parameter | Conditions | Min. | Typ. | Max. | Units | Gain | - | 24 | 25 | 26 | dB | Input Sensitivity(RMS) | @4Ω, 50W, 1KHz | - | 808 | - | mV | Input Impedance | - | - | 22 | - | KΩ | Output Power | @4Ω THD+N 1% | - | 36 | - | W | @4Ω THD+N 10% | - | 50 | - | W | Bandwidth @ ±3dB | @4Ω | 20 | - | 20K | Hz | THD | @4Ω, 1W, 1KHz | - | 0.0299 | - | % | @4Ω, 10W, 1KHz | - | 0.073 | - | % | Output Noise Level | A-weighting,Input Connected to GND | - | 82.8 | - | µV | SNR | 36W @4Ω THD+N 1% | - | 100 | - | dB
|
2 x 25Watt @ 4ohm Class-D Audio Amplifier Board -TPA3123
Specification: Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of TPA3123 chip. See Test/Application Circuit. Unless otherwise specified, VDD = 24V, f = 1kHz, Measurement Bandwidth = 22kHz, RL = 4Ω, TA = 25 °C, Package heat slug soldered to 2.8 square-inch PC pad. Parameter | Condition | Min. | Typ. | Max. | Supply Voltage | | 10V | 24V | 30V | Output Power | RL=4Ω,Vin=27V | | 25W | | Output Power (Continuous Average/Channel) | THD+N = 0.08% RL =4Ω RL = 8Ω THD+N = 10% RL = 4Ω RL = 8Ω | | 10W 5 W 20W 10W | | Mute Supply Current | MUTE = GND | | 23mA | 37mA | Sleep Supply Current | SLEEP = GND | | 0.39mA | 1mA | Total Harmonic Distortion Plus Noise | PO = 10W/Channel | | 0.08% | | Signal-to-Noise Ratio | A-Weighted , RL = 4Ω | | 99dB | | Note: 1. Minimum and maximum limits are guaranteed but may not be 100% tested. 2. DC bias has been set, we recommend no longer tune.
|
2 x 15Watt @ 8ohm Class D Audio Amplifier Board - MAX9736A
Specification: Following table lists all typical data of the Amp board. For full specification, please refer to thedata sheet of MI’s MAX9736A chip. TA = 25℃, fIN = 1 kHz sine wave, RL = ∞, VVS = 5V. (Unless otherwise stated) Parameter | Conditions | Min | Typ | Max | Supply Voltage (V) | Inferred from PSRR test | 8 | - | 28 | Quiescent Current (mA) | RL = ∞, VREGEN = 5V, VVS = open | TA = +25°C | | 30 | 45 | TA = TMIN to TMAX | - | - | 50 | RL = ∞, VREGEN = 0V, VVS = 5V | TA = +25°C | | 14 | 20 | TA = TMIN to TMAX | - | - | 22 | Input Sensitivity (V) | - | - | 0.833 | - | Input Impedance (Kohm) | - | - | 22 | - | Gain (dB) | MAX9736A | 16.5 | 17 | 17.5 | Output Power (THD+N= 1%) (W rms) | VPVDD = 12V | RL = 8Ω | - | 8 | - | RL = 4Ω | - | 13 | - | VPVDD = 18V | RL = 8Ω | - | 13.5 | - | VPVDD = 24V | RL = 8Ω | - | 13.5 | - | Output Power (THD+N= 10%) (W rms) (Thermal limited) | VPVDD = 12V | RL = 8Ω | - | 10 | - | RL = 4Ω | - | 15 | - | VPVDD = 18V | RL = 8Ω | - | 15 | - | VPVDD = 24V | RL = 8Ω | - | 15 | - | Efficiency (%) | PO = 8W, MAX9736A, PVDD = 12V ,RL = 8Ω | - | 88 | - | Minimum Load (ohm) | - | - | 8 | - | Frequency Response (Hz) | ±3dB | 20 | - | 22k | Operating Temperature (℃) | - | 0 | 20 | 50
|
2 x 20Watt @ 8ohm Class D Audio Amplifier Board - MAX98400A
Specification: Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of MI’s MAX98400A chip.TA = 25℃, fin = 1 kHz sine wave, RL = ∞, VVS = 18V. (Unless otherwise stated)Parameter | Conditions | Min | Typ | Max | Supply Voltage (V) | Inferred from PSRR test | 8 | - | 28 | Quiescent Current (mA) | RL = ∞, VREGEN = 5V, VVS = open | TA = +25°C | | 30 | 45 | TA = TMIN to TMAX | - | - | 50 | RL = ∞, VREGEN = 0V, VVS = 5V | TA = +25°C | | 14 | 20 | TA = TMIN to TMAX | - | - | 22 | Input Sensitivity (V) | - | - | 0.62 | - | Input Impedance (Kohm) | - | - | 22 | - | Gain (dB) | MAX98400A | | 26.4 | | Output Power (THD+N= 10%) (W rms) (Thermal limited) | VPVDD = 18V | RL = 8Ω | - | 22 | - | RL = 4Ω | - | 44 | - | Efficiency (%) | PO = 8W, MAX98400A, PVDD = 12V ,RL = 8Ω | - | 91.2 | - | Minimum Load (ohm) | - | - | 8 | - | Frequency Response (Hz) | ±3dB | 20 | - | 22k | Operating Temperature (℃) | - | 0 | 20 | 50 |
2 x 25Watt @ 8ohm Class D Audio Amplifier Board - TDA7492P
Specification: Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of MI’s TDA7492P chip.TA = 25℃, fin = 1 kHz sine wave, RL = ∞, VVS = 5V. (Unless otherwise stated)Parameter | Conditions | Min | Typ | Max | Supply Voltage (V) | Inferred from PSRR test | 8 | - | 26 | Quiescent Current (mA) | RL = ∞, MUTE=open, STBY = open | TA = +25°C | - | 30 | 40 | TA = TMIN to TMAX | - | - | 45 | RL = ∞, MUTE=open, STBY = GND | TA = +25°C | - | 8 | 10 | TA = TMIN to TMAX | - | - | 12 | Input Sensitivity (V) | - | - | 0.63 | - | Input Impedance (Kohm) | - | - | 22 | - | Gain (dB) | TDA7492P | - | 27.6 | - | Output Power (THD+N= 1%) (W rms) | VPVDD = 12V | RL = 8Ω | - | 7.2 | - | VPVDD = 20V | RL = 8Ω | - | 20 | - | Output Power (THD+N= 10%) (W rms) (Thermal limited) | VPVDD = 12V | RL = 8Ω | - | 9.5 | - | VPVDD = 20V | RL = 8Ω | - | 25 | - | Efficiency (%) | PO = 25W, TDA7492P, PVDD = 12V ,RL = 4Ω | - | 92 | - | Minimum Load (ohm) | - | - | 8 | - | Frequency Response (Hz) | ±3dB | 20 | - | 22k | Operating Temperature (℃) | - | 0 | 20 | 50 |
2 x 50Watt @6Ohm Class D Audio Amplifier Board Compact - TDA7492
Specification: Following table lists all typical data of the Amp board. For full specification, please refer to the data sheet of MI’s TDA7492 chip. TA = 25℃, fIN = 1 kHz sine wave, RL = ∞, VVS = 5V. (Unless otherwise stated) Parameter | Conditions | Min | Typ | Max | Supply Voltage (V) | Inferred from PSRR test | 8 | - | 26 | Quiescent Current (mA) | RL = ∞, VREGEN = 5V, VVS = open | TA = +25°C | - | 70 | 90 | TA = TMIN to TMAX | - | - | 100 | RL = ∞, VREGEN = 0V, VVS = 5V | TA = +25°C | | 50 | 60 | TA = TMIN to TMAX | - | - | 62 | Input Sensitivity (V) | - | - | 0.792 | - | Input Impedance (Kohm) | - | - | 22 | - | Gain (dB) | TDA7492 | 26.6 | 27.6 | 28.6 | Output Power (THD+N= 1%) (W rms) | VPVDD = 25V | RL = 6Ω | - | 40 | - | Output Power (THD+N= 10%) (W rms) (Thermal limited) | VPVDD = 25V | RL = 6Ω | - | 50 | - | Efficiency (%) | PO = 40W, TDA7492, PVDD = 25V ,RL = 6Ω | - | 90 | - | Minimum Load (ohm) | - | - | 6 | - | Frequency Response (Hz) | ±3dB | 20 | - | 22k | Operating Temperature (℃) | - | 0 | 20 | 50 |
2 x 30Watt Class D Audio Amplifier Board -TPA3118
Specification: Parameter | Condition | Min | Typ | Max | | Supply Voltage (V) | | 9 | 21 | 24 | | Quiescent Current(mA) | Standby Powered by 21V DC | | 1 | | | EN Floating Powered by 21V DC | | 36 | | | | Input Sensitivity(VRMS) | | | 1.04 | | | Input impedance | | | 30K | | | Gain (dB) | | | 26 | | | Output Power(W) | 8ohm 21V DC THD+N 10% | | 30 | | | 8ohm 21V DC THD+N 1% | | 24.5 | | | Efficiency | 2X30W @8ohm powered by 21V DC | | 92% | | | | Minimum Load(ohm) | | | 3.2 | | | Frequency Response | +/-3dB | 20Hz | | 20KHz | | Operating Temperature Degrees Celsius | | 0 | 25 | 50 |
|
1 x 60Watt Class D Audio Amplifier Board -TPA3118
Specification: Parameter | Condition | Min | Typ | Max | | Supply Voltage (V) | - | 9 | 21 | 24 | | Quiescent Current(mA) | Standby Powered by 21V DC | - | 3 | - | | EN Floating Powered by 21V DC | - | 30 | - | | | Input Sensitivity(VRMS) | - | - | 1.18 | - | | Input impedance | - | - | 30K | - | | Gain (dB) | - | - | 26 | - | | Output Power(W) | 4ohm 21V DC THD+N 10% | - | 60 | - | | 4ohm 21V DC THD+N 1% | - | 45 | - | | Efficiency | 1X60W @4ohm powered by 21V DC | - | 91% | - | | Minimum Load(ohm) | - | - | 1.6 | - | | Frequency Response | +/-3dB | 20Hz | - | 20KHz | | Operating Temperature Degrees Celsius | - | 0 | 25 | 50 |
1 x 40Watt Class D Audio Amplifier Board -TPA3110
Specification: Parameter | Condition | Min | Typ | Max | | Supply Voltage (V) | | 8 | 19 | 24 | | Quiescent Current(mA) | Standby Powered by 19V DC | | <1 | | | EN Floating Powered by 19V DC | | 70 | | | | Input Sensitivity(VRMS) | | | 0.66 | | | Input impedance | | | 30K | | | Gain (dB) | | | 26 | | | Output Power(W) | 4ohm 19V DC THD+N 10% | | 40 | | | | 4ohm 19V DC THD+N 1% | | 30 | | | Efficiency | 1X40W @4ohm powered by 19V DC | | 88% | | | Minimum Load(ohm) | | | 3.2 | | | Frequency Response | +/-3dB | 20Hz | | 20KHz | | Operating Temperature Degrees Celsius | | 0 | 25 | 50 | |
1 x 30W Class D Audio Amplifier Board - TPA3110
Specification: Parameter | Condition | Min | Typ | Max | | Supply Voltage (V) | | 8 | 16 | 19 | | Quiescent Current(mA) | Standby Powered by 16V DC | - | <1 | - | | | EN Floating Powered by 16V DC | - | 40 | - | | Input Sensitivity(VRMS) | - | - | 0.62 | - | | Input impedance(ohm) | - | - | 30k | - | | Gain (dB) | - | - | 26 | - | | Output Power(W) | 4ohm 16V DC THD+N 10% | - | 30 | - | | | 4ohm 16V DC THD+N 1% | - | 20 | - | | Efficiency | 1X30W @4ohm powered by 16V DC | - | 87% | - | | Minimum Load(ohm) | - | - | 3.2 | - | | Frequency Response | +/-3dB | 20Hz | | 20KHz | | Operating Temperature Degrees Celsius | - | 0 | 25 | 50 | |
Kindly Note:The Red marked products will be soon released. The Green backlight marked products is Top selling product
|