Peel ‘n’ Stick Clear Traction Grip Great for Surfboards, SUP’s, Wake Skates and more.
You are bidding on a sample piece Hexagonal about 145mm diameter from corner to corner .
Made from a patent-pending textured space-aged composite surface.
It is engineered to provide outstanding anti-slip properties in both wet and dry conditions.
All traction can be trimmed to fit if necessary.
There is now no need to put toxic wax on your boards and mess up your board bags.
This will also save you money and keep your board looking great.
Now available for short boards, longboards, stand ups , fishes, mini mals etc etc.
Can be used for boat decks also.
These are so thin (maybe 1mm) will not create any drag in the water.
Paddle grips are 90mm wide - you can split these down the middle and use as rail tape for your stand up board.
Packs can be split if required
Replacement pieces are also available
Features -
Is not black foam so is not going to get hot to stand on in the sun
Waxless surfboard traction
No Rash
Clear grip tape
Replaces wax
Wax may still be applied
Any hot water or air temperature will not effect this
No melting wax
No dirty board bags
No need to buy more wax
Lighter than heavy wax build up
No sand sticking to your wax
Protection of your board
No lumpy wax sections
Cheaper than wax
Lighter than wax
Durable, reliable everytime and any where around the world
2 year warranty and 1 year adhesive warranty
You must make sure your board is clean and dry before adhering your traction pads
Used By Pro Surfer Sunny Garcia and Chris McCormack Hawaiian Iron Man Champion 2 times and Mark Riley
Free Sticker
SIZING
Here are the sizes – these can be trimmed with scissors or Stanley knife – they would normally have a spacing of 1/8” or 3mm up to ½” or 12mm see the attached diagrams.
Fish –
Actual sizing of grip - length 1800mm or 5’11” Width 505mm or 20”
Maximum size board - length 2100mm or 7’0” Width 570mm or 22 ¾ ”
Fun board/Mini mal -
Actual sizing of grip - length 2350mm or 7’9” Width 520mm or 20 ½ ”
Maximum size board - length 2575mm or 8’7” Width 585mm or 23 ¼ ”
Short board – needs a tail pad maybe an enviro cork one - http://www.balsasurfboardsriley.com.au/Eco-friendly-surf-supplies.html order here for $58
Actual sizing of grip - length 1030mm or 40 ½ ” (centre) length 1170mm or 42 ” (outside near rail) Width 470mm or 18 ½ ”
Maximum size board - length 2250mm or 7’6” Width 535mm or 21 ¼ ”
Longboard
Actual sizing of grip - length 2200mm or 8'6 ½” (centre) Width 560mm or 22”
Maximum size board - length 2700mm or 9’0” Width 590mm or 23”
So the nose length is 22” or 560
2nd section 15” or 380mm
3rd section 23” or 590mm
Tail section 26” or 670mm
Stand – up paddle grip
Actual sizing of grip - length 410mm or 16 ½” Width 90mm or 3 1/2”
suitable to protect your rail of your paddle board also
You are bidding on 1 hexagonal piece - they are 145mm from corner to corner. If you purchase more than 10 pieces the price drops to $4 each
FREE DELIVERY FOR THE SECOND AND THIRD UNIT
https://www.youtube.com/watch?v=YdMtRWiZuBc
https://www.youtube.com/watch?v=xbqr-XTcZ30
https://www.youtube.com/watch?v=CaguTtZNjBo
https://www.youtube.com/watch?v=XoDjmFcTfEw
https://www.youtube.com/watch?v=MheiSbsaUkg
https://www.youtube.com/watch?v=A7mmXsH9ciU
https://www.youtube.com/watch?v=BVWhk34Xi0Q
FOR MORE INFO GO TO
TESTIMONIAL Dear rileybalsa1234, |
|
||
|
Plus delivery or Pick up Miranda 2228
Pick up $0
Australian shipping $17
Europe shipping $35
Rest of the world shipping $30
Hi Mark. As asked (sorry for the delay), attached are a couple of photos of the board with the Versagrip on. Thought I might post a couple of tips for its application as it can be fiddly to apply.
WAX REMOVAL
Soften it up in the sun or with some warm water and scrape it off with a plastic flat wax comb (or piece of balsa) and then wipe it off with a rag and mineral turps and clean up with a soft clean dry t-shirt.
When applying, I found it best to start from the stringer (get someone to help you – with clean dry hands) - position the grip up to the location you want then working your way outwards towards the rails (preventing air pockets along the way). This I found to be best (better than horizontal - down the board application) for a bilateral symmetrical placement either side of the stringer. Also don't hold onto the adhesive for too long as it will come off on your finger & thus affect adhesion in that part of the grip. Live & learn as they say. Need just a little wax on chest where wetsuit touches.