18650 Li-ion Lithium Battery ZB2L3 Capacity Tester & Lithium Battery USB Cable

Popular

    Product Introduction

    Description:
    Lithium meter tester ZB2L3 

    100% brand new and high quality
    Material: Electrical components
    ZB2L3 battery capacity tester discharge type 1.2-12V external load capacity of the battery and other tests 18650
    Tools, single-function, by controlling the load off and get real-time integrated discharge current capacity results
    Maximum support 15V 3A discharged through the discharge voltage and current, itself does not discharge
    Maximum capacity statistics support 9999Ah (9999000mAh)
    Automatically identify and develop appropriate battery termination voltage can also be manually adjusted

    Specifications:
    Power supply voltage: DC4.5-6V (micro USB connector)
    Operating Current: less than 70mA
    Discharge voltage: 1.00V-15.00V 0.01V resolution
    Termination voltage range: 0.5-11.0V
    Supported by current: 3.000A 0.001A resolution
    Maximum voltage measurement error: 1% + 0.02V
    Maximum current measurement error: 1.5% + - 0.008A
    Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value by shifting the decimal point to switch, when the display is less than 10Ah X.XXX, as shown above to achieve 10Ah XX.XX, and so on.
    Board size: 50mmX37mm
    Finished Size: 50mmX37mmX17mm (length X width X height maximum position size, contains copper foot height)

    Instructions:
    1. The first test should be fully charged battery.
    2. Connect the battery to be tested positive to positive input, a negative input to the negative, can not be reversed (with load reversal may damage the circuit)! Load connected to the output of the positive and negative output, to work through the tester micro USB power supply (not available desktop or laptop USB powered), then the battery voltage.
    3. Direct start test need only one press of the "OK" button, the tester can automatically develop an appropriate termination voltage of the battery full charge voltage, and will start flashing after the test three times. Need to develop artificial termination voltage only when the battery voltage display state by pressing "+" or "-" buttons to modify the termination voltage display beginning with P, behind the representative voltage resolution 0.1V, set up after pressing the "OK "start testing.
    4. After the start of the test the tester will control the load of the electronic switch is turned on, the test data shows that the process will release capacity (Ah), current discharge current (A) and battery voltage (V) between the wheel was. When the battery voltage reaches the set cut-off voltage, load control switches off the tester display data stays in capacity (Ah) and above and the corresponding indicator flashes quickly together, now displays the actual capacity of the battery is discharging capacity, about the press "OK" to terminate flashing allows stable data display, press again "OK" button to return to the power-on state can just replace the battery test the next section ......

    Error codes and their meanings:
    Err1: battery voltage is above 15V
    Err2: battery voltage is lower than the termination voltage
    Err3: Battery can not afford to load or discharge current line too much resistance
    Err4: overcurrent (current exceeds 3.1A)
    This circuit voltage in order to improve the measurement accuracy, specially designed DC bias, when the terminal displays nothing then a small voltage does not affect the actual measurement, if you are shorting the input terminals (absolute 0V) will show 0
    Note: Use the resistance of the discharge process, resistive load will seriously heat, please pay attention to safety!
     Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!

    Package Included:
    1PC*battery capacity tester .1Pc x Load resistors
    Lithium Battery USB Cable

    The USB battery charger cable with JST plug, output 3.7V 500ma, is suit for JST 3.7V(1S) Lipo battery.
    Note: For Lipo battery only, do not use for Ni or Ni-Cd battery.

    Package Included:
    1PC*USB battery charger cable (Not included battery)
    • We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
    • Payment must be received in 5 business days of auction closing.
    • Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
    • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
    • We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
    • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
    • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
    • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.

    DataCaciques