How to User It?
1.Switch Displayed Parameters:
In the normal interface, short press SW to switch the displayed content in the lower line. Current A, power W, capacity Ah, and time h can be switched. Long press to change the top displayed content, switching between input voltage IN and output voltage OUT.
2.Set Output Voltage Value:
In the normal interface, short press U / I button to enter into voltage CC setting interface. A certain digit of set output voltage is blinking. Rotate the encoder knob to increase or decrease output voltage. Short press the knob to select which digit of the output voltage to set. When the setting is completed, short press U / I button twice to return to the normal interface. Or it will automatically return to the normal interface, without operation in 10s.
3. Set Constant Current Value (That is, the maximum output current allowed by the module):
In the normal interface, short press U / I button to enter voltage constant current setting interface. Short press U / I button again to switch to set constant current value. It can be seen that a certain bit of the constant current value is blinking. Turn the encoder knob to increase or decrease the value. Short press the encoder to select which digit of the constant current value to set. When the setting is completed, short press U / I button to exit the setting interface and return to the normal interface. Or it will automatically return to the normal interface, without operation in 10s.
4. Set the Module to be ON/OFF by Default:
In the normal interface, press and hold U / I button to enter parameter setting interface. It displays OPEN OFF or OPEN ON. OPEN OFF means the output is turned off by default when power-on, and OPEN ON means the output is turned on by default when power-on. Press and hold the rotary encoder to switch between these two states. After the setting is completed, press and hold the U / I button to return to the normal interface.
5. Set Protection Parameters ON and Threshold:
In the normal interface, press and hold U / I button to enter parameter setting interface. Short press SW button until the protection parameter you want to set appears.
LUP: Under-voltage protection threshold
OUP: Over-voltage protection threshold
OCP: Over-current protection threshold
OPP: Over-power protection threshold
OAP: Over-capacity protection threshold
OHP: Timeout protection threshold
OTP: Over-temperature protection threshold
Short press the rotary encoder to select which digit of the protection parameter you want to set. Long press the encoder to set protection parameters ON or OFF (Note: Only timeout protection and over-capacity protection can be set on / off, other protection parameters are turned on by default.). Rotate the encoder to change the parameters. After the setting is completed, press and hold U / I button to return to the normal interface.
6. Voltage & Current Calibration:
In the normal interface, press and hold U / I button to enter parameter setting interface. Short press SW button until the parameter interface with CAL appears.
Interface with CAL + IN + V is the input voltage calibration interface
Interface with CAL + OUT + V is the output voltage calibration interface
Interface with CAL + OUT + A is the output current calibration interface
Rotate the encoder left and right to adjust parameters. Press and hold the encoder to confirm that the adjustment is complete. At this time, the parameter value does not flash. Long press the U / I button to return to the normal interface.
Attention: To ensure the accuracy of calibration, only when the voltage is over 12V can voltage be calibrated. And only when the current is over 1A can current be calibrated.
Note:
- The input terminal IN- of the module must not be short-circuited with the output terminal OUT-, otherwise the constant current function will fail.
- Please ensure that the power of your power supply is greater than the power required by the output load.
- When users need the module to output at full load, input voltage needs to be larger than 8V. When input voltage is 5V, output power is about 15W. The maximum current of module is 4A, which is limited by the maximum output power. For example, if the output is 17V, current should not be greater than 2A.
- When this module is used over 3A, 35W, please strengthen heat dissipation devices.
- The module has input under-voltage protection function. The default value is about 4.8V (can be set). If it is lower than this value, output will be automatically disconnected (Attention: The voltage at the port of module is lower than the under-voltage protection threshold. When input current is relatively large, please not ignore the divided voltage on input wire).
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can perform up your satisfaction.
It is impossible to address issues if we do not know about them!
1. 12 months Manufacturer’s limited Warranty for defective items (excluding items damaged and/or misused after receipt). Accessories come with a 3-month warranty.
2. Defective items MUST BE reported and returned within the warranty period (and in the original packaging, if possible). You must tell us what the defect is and give us your order number. WE DO NOT REPAIR OR REPLACE ITEMS WITH AN
EXPIRED WARRANTY.
1. You have 7 days to contact us and 30 days to return it from the date received. If the item is in your possession more than 7 days, it will be considered used and WE WILL NOT ISSUEA REFUND OR REPLACEMENT to you. There are NO EXCEPTIONS!
Shipping cost is bear by both seller and buyer in half.
2. All returned items MUST BE in the original packaging and you MUST PROVIDE us with the shipping tracking number, specific reason for the return, and your order ID.
3. We will refund YOUR FULL WINNING BID AMOUNT, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER BOTH Buyer and Seller cancel the transaction from aliexpress. OR, you may choose to have a replacement.
4. We will bear all the shipping cost if the product(s) is (are) not as advertised.