The Timpano TPT-DH175 is a 1″ phenolic dome compression driver specially designed to offer a smooth extended frequency response over a broad band, from mids to highs, with very high efficiency.

Easy to install anywhere, even on car doors. In addition, the small diameter of the compression driver allows simple installation at the front. This horn driver can deliver space filling sound at extremely high SPL levels, a great choice for high output PA, home theater, and car audio systems.

Ideal for compact 2 or 3-way systems. The 4.5″ x 4.5″ horn TPT-HL11-25 produces a controlled 45° x 45° dispersion pattern to reduce unwanted reflections while still delivering room filling sound. As a replacement for pro audio cabinets, this high frequency horn driver has a common footprint.

Specs:
250 Watts Max Power
75 Watts RMS Power
Impedance: 8 Ohm
Sensitivity: 108 dB
Frequency Response: 1.3 kHz – 19 kHz
1″ Voice Coil
Phenolic Diaphragm
Ferrite Driver
Recommended High Pass Filter on TPT-SP4BT DSP Crossover
1400 Hz under 125 Watts of Amplifier RMS Power with 18dB Slope
1200 Hz under 75 Watts of Amplifier RMS Power with 12dB Slope
Sizing:
Mounting Depth: 4.64″ (117.8 mm)
Mounting Cutout size: 3.50″ x 3.50″ + Terminal
Overall size: 4.50″ Wide x 4.50″ Length x 4.92″ Height
Weight: 1.15 Lbs

TPT-500 2 Ohm

• COMPACT DESIGN: Digital class D Brazilian technology allows this amplifier to have a small footprint by integrating a high-speed mosfet power supply with top of line transistors to ensure performance in a small heat sink without compromising performance. Dimensions: 3.93″ depth x 5.02″ width x 2″ height
• POWER: This amplifier is designed to run your system with the power it needs to perform! 500 Watts maximum dynamic RMS power output on one channel. Its high efficiency rate of 85% provides more power with less battery consumption.
• HIGH LEVEL INPUTS with SIGNAL AUTO TURN ON: Attaches directly to systems using speaker-level inputs with signal auto turn-on to eliminate remote turn-on wiring
• TECHNOLOGY: A smart electronic 2-way protection circuit protects the amp if it gets too hot or if speakers fail causing a short! Focusing in sound quality, a full range response of 10 to 22,000Hz was used to give the best sound reproduction on this tiny amplifier.
• FEATURES: Heavy Duty 10 Gauge power and speaker wire Inputs. Built-in crossover filters for easy tuning! Built-in variable crossover filters: HPF ( 10 – 700Hz ) and LPF ( 60 – 22 KHz ). It also includes Variable Gain Control. Level controls are not for adjusting volume. They adjust the amount of signal that is coming into the amplifier from your signal source.

Additional Information:

Number of Channels: 1
Max Dynamic Output: 500 Watts RMS 2 Ohm
380 Watts RMS Power at 2 Ohm 12.6 Volts
150 Watts RMS Power at 4 Ohm 12.6 Volts
Supply Voltage: 10 ~ 15V
Frequency Response: 10Hz ~ 22KHz
LPF – Crossover Low Pass: 60Hz to 22,000 Hz
HPF – Crossover High Pass: 10Hz to 700 Hz
Signal to Noise: > 90 dB
Harmonic Distortion: < 0.9 % THD
Input Impedance: 10K Ohm with RCA and 38K Ohm with Wires
Impedance Output: 2 Ohm
Consumption with Signal Musical: 1A ~ 18A
Dimensions (L x W x H): 3.93” x 5.02” x 2”
Weight: 1.12 Lbs