You may also like
Product Description
Note : This inverter do not have the monitoring function.
800W waterproof grid tie inverter,pure sine wave inverter.
DC20V-50V to AC110V or 220V,50Hz/60Hz auto.
Waterproof IP65.Use for 24v/36v solar panel.
LED Display
1.Red light 3 second---Red LED light 3 secondwhile device starts , then in working condition;
2.Green flash fast---MPPT searching;
3.Green flash slow---MPPT + searching;
4. Red flash slow---MPPT - searching;
5.Green lights on 3s and off 0.5s---MPPT locked;
6.Red light steady---
a. Islanding protection;
b.Over-temperature protection;
c.Over 1 low AC voltage protection;
d. Over/ low DC voltage protection; e.Fault
System Function
◆ 6-grade power search---In overcast weather, the PV Panel' s output current is extremely tiny, then inverter will automatic
open 6-grade power search function,and keep outputing efficent and steady during the low power.
Wide voltage input(22-50VDC)---1.DC voltage input:22~50VDC; 2.Second level power variable voltage conversion.
High-frequency two-way and one-way grid function---1.High frequency direct modulation, AC half wave synthesis;
2.Two-way grid means: Load consume directly. And can reverse AC current transmission.
Kinds of frequency output function---1.It can apply to 50Hz and 60Hz frequency of AC;
2.Frequency range: 45Hz~64Hz;
◆Directly connected to the solar panels (do not need to connect the battery)
◆ AC O angle with high precision auto-detection---High-precision analysing the AC phase angle .The phase shift rate is less
than 1%, thus achieve high-precision with phase modulation AC output together.
1.AC phase shift:<1%; 2.Over-zero protection: 0.2 VAC; 3.AC switching: 50Hz/60Hz.
Synchronous High-frequency Modulation
1.Modulation synthesis: half wave and full-bridge modulation synthesis (100Hz/120Hz2);
2.Synthetic way: MOSFET full-bridge; 3.High frequency: 50KHz.
Pure Sine Wave Output---Use SPWM directly to make pure sine wave output.
1.Output waveform: Adopt complementary PWM to push-pull pure sine wave;
2.Generate means: enhancement-mode SPWM.
Power Automatically Locked (APL)--- automatically powers locked in maximum power point, made output more stable.
Constant Current, Constant Power---constant current and output power, without any overload, over-current phenomenon.Exactly and timely automatic Island Effect Protection
High-Frequency High Conversion Rate---Adapt high frequency converter, the output more efficient.
Maximum Power Point Tracking (MPPT)---high-precision (MPPT) operation power, automatic and immediate adjust the solar
panels output power at the maximum output point,made the inverter discharge to power grid with the highest efficiency.
Stack using---Such as: 4 micro inverter of 260W stacking can achieve 1040W. the number of the stacking is unlimited.
DC input---Input voltage range: 22V to 50V,PV Panel: Recommend using the power more than 30W and the standard voltage of 36V PV panels.Suggestion making the PV in parallel.
AC output---220VAC:180V-262V, 50HZ;110V AC:80V-160V.60HZ.
1. The inverter is designed to handle PV panels as input source only and will not work with batteries/wind turbines as input source.
2. The solar panels Voc voltage needs to be more than 31V less than 50V input.
3. The minimum power for solar panels should be half the power of the inverters.
4. If the red LED light on or all LED lights are off, please contact us first. Sometimes replacing some AC or DC side parts can make the item work again.
5. Try to cover the product as much as possible during installation to prevent rain or mist from entering the product.
6. If a good environment for cooling is not available, a fan can be added outside of the item to allow for cooling.
Package:
1.One user manual;
2.One 800W inverter;
3.One AC Cable;