50ml Kafuter UV Glue UV Curing Adhesive K-300

Transparent Crystal and Glass Adhesive with UV Flashlight



Product Features:

K-300 is a modified UV or visible light curing acrylic adhesive, low odor, high transparency, high bonding strength,low viscosity, easy deaeration , typically used in large- area glass crystal bonding, such as : glass mosaic,glass crafts, crystal crafts.


Key performance indicators:

Appearance: colorless or light yellow transparent liquid

Viscosity cps: <110 (Brookfield DV-II viscometer , 25 ° C, SC 4-15 rotor 150rpm)

Hardness ( Shore D): 75 (GB / T 531-1999 curing test )


Typical curing nature:

K-300 will be cured under ultraviolet light , the sun will slowly solidified . 220-260nm light source helps surface cure .

Cure rate , depth, and ultimately curing effect is dry and UV light source , exposure time , light transmittance related material . Suggested by experiments to determine the final curing process .


Positioning time:

10 seconds -125w high-pressure fluorescent , 4 mW / cm ⊃2; UVA


Full cure time:

180 seconds -125w high-pressure fluorescent , 4 mW / cm ⊃2; UVA


Typical cured properties:

Tensile shear strength (GB 7124-86) overlapped area of 25 × 12.5 = 312.5mm2: glass / stainless steel , ≥ 10MPa


Use these steps:

1 Depending on the material surface treatment , surface dry and clean , no weak boundary layer ;

2 interface adhesive bonding material on the need for continuous coating, be careful not to disperse ;

3 light positioning the glue into the short ultraviolet curing lamp radiation, until the hand nudging fixed;

4 to remove the excess glue with a knife to scrape the glue overflow , or a soft cloth , paper towel and gently erase the excess glue can also be dipped in acetone, alcohol wipe ;

5 full cure time high radiation , until fully cured , note the temperature is not too high ;

6 dipped in acetone, alcohol, cleaning materials with a soft cloth or paper towel and gently wipe the bonding good material .


Instructions for use:

1 , the adhesive surface clean, dry and free of grease , you can wipe with acetone , hair dryer .

2, the UV lamp positioned curing , the curing rate is dependent on the glue to absorb light energy from the light source associated with , the light transmittance material and other factors .

3 , the operation should not squeeze too hard to be sticky , and shall not be repeatedly moved apart

adherend.

4, using the rest of the glue not fall back to the original packaging to avoid contamination.



Note:

Avoid contact with eyes, skin and clothing . This pair of eyes and a slight skin irritation.

If accidentally splashed into the eyes , rinse immediately with plenty of water , as there does not need to go to hospital.

Rinse immediately with soap and water after skin contact. Please wash before they can wear the clothing.

Do not allow contact with children .


Storage: This product is sensitive to light and heat , you need storage in a cool, dry place, away from light below 28 ° C, valid for one year .




Note :flashlight(not include battery)

K-300 is a modified UV or visible light curing acrylic adhesive, low odor, high transparency, high bonding strength,low viscosity, easy deaeration , typically used in large- area glass crystal bonding, such as : glass mosaic,glass crafts, crystal crafts. Cure rate , depth, and ultimately curing effect is dry and UV light source , exposure time , light transmittance related material . Suggested by experiments to determine the final curing process . 4 to remove the excess glue with a knife to scrape the glue overflow , or a soft cloth , paper towel and gently erase the excess glue can also be dipped in acetone, alcohol wipe ; 2, the UV lamp positioned curing , the curing rate is dependent on the glue to absorb light energy from the light source associated with , the light transmittance mater