NOTE: 1,Mounting brackets can be mounted horizontally or vertically depending on what fixture there is to install shades onto. After determining location to install mounting brackets, use bracket as template to mark hole positions for pre-drilling holes in surface for insertion of plastic anchors. NOTE:2 ,If medium onto which brackets will be mounted to is solid wood, plastic anchors are not necessary. Directly install with just screws if desireed. For other medium such as concrete or stone, anchor is required. After holes are drilled, insert plastic anchors into hole until flush with surface. If needed, lightly tap anchor into hole with hammer. Then attach brackets to surface with screws. NOTE:3,Mountinq Vertically Remove the four screws from both b『ackets. Turn the Clutch Unit 90 degrees so the clutch eyelet hangs straight down if the Clutch were hang-ing from the top, and turn the Idle End Unit so the opening is facing away from the window. Put screws back in. NOTE:4,Last step is to install bracket holders for the bungee cord and ring that is tied to the ends of the shade. This is used to help tie down the shade during windy conditions. Install the bracket at a side location like with the mounting brackets. Make sure each bracket is at least 6 feet from the top of the shade and can be reached by bungee cord. Insert ring into the bracket to secure NOTE:5,Remove the four sc『ews. Turn the clutch unit 180 degrees so the wand eyelet can now hang down from the left side. Put the screws back in, and tighten. No change is needed to the Idle End Unit, it works for right and left mounts. Pull out both End Plugs from the tube and switch them. All Replacement Parts for Exterior Sun Shades is HERE. All Hardware for the Exterior Sun Shades. Cross Land Exterior Sun Shades Accessories,Universal Accessory of Exterior Sun Shades,Repair your Exterior Sun Shade. Measure the Dia of your upper Alu tube, You can choose thee Clutch Plug 38mm or 28mm. 1. First, insert the Clutch plug into the Crank unit . 2. Insert the Idle end plug into the Idle end unit, and snap the Idle end plug securely into place . With the Shade in place, adjust the brackets so they fit snugly on each end of the Shade ALTERNATIVE CLUTCH SETUP Your Shade will require a non-standard installation if: you are changing the Clutch to the left side of the Shade, or if you are mounting your Shade from the top/ceiling. NOTE: If you purchased a custom Shade or are doing a standard installation, you do NOT need to make these changes.A. If you want your Clutch to be on the left side ofyour Shade, you will need to make a simple change to your Crank unit before you install your Shade. To make this change, remove the four screws . B. Turn the Crank unit 180° so the wand eyelet can now hang down from the left side C.Put the screws back in, and tighten. No change is needed to the Idle end unit, it works for right and left mounts. CHANGE TO A TOP CEILING MOUNT If you want your Shade hang from the top (for example, the ceiling), you will need to make a simple change to your Crank unit and Idle end unit before you install your Shade. A. Remove the four screws from both brackets B. Turn the Crank unit 90° so the Clutch eyelet hangs straight down. If the Clutch were hanging from the top, and turn the Idle end unit so the opening is facing away from the window , put screws back in Product Description
Cross Land Exterior Sun Shades Accessories
Item model number | CMCK-Accessory-01 |
Volume | 27.5 Cubic Inches |
Room Type | Dining Room |
Number of Items | 1 |
Mounting Type | Outside Mount |
Number of pieces | 1 |
Color | Beige |
Pattern | Solid |
Product Dimensions | 3.2"L x 2.5"W |
Material | Plastic |
Water Resistance Level | Not Water Resistant |
Shape | Square |
Item Weight | 9.9 ounces |
Batteries required | No |
Operation Mode | Manual |
Size | Cordless Bracket |
Is Discontinued By Manufacturer | No |
Included Components | Screws |
Shipping
Returns and payment
FeedBack
For any questions, using eBay contact system