1.Description
This manual resistor-forming machine is easy to operate and master. You can adjust the size of each processing part with the non-slip adjustment knob to meet your different needs for processing components. Its all-metal construction is durable and wear-resistant, ensuring a long service life. It will be your ideal choice!
Specification Housing Material: Iron Cutter Material: Steel Fixing Bar Material: Solid Steel Hand Shank Material: Solid Cast Iron Surface Treatment: Painted Craftsmanship: Quenched and Forged, Hardened Color: Blue, Black, Silver Packing Size: 34*31*40cm/13.38*12.2*15.74in Product Size: 20*20*17.5cm/7.87*7.87*6.88in Hanging Pole Length: 19cm/7.48in Hand Shank Length: 16cm/6.29in Handle Length: 10cm/3.93in Gross Weight: 12kg/26.45lbs Net Weight: 10kg/22lbs | ![]() |
Package Included 1 x Resistor Forming Machine 1 x Hanging Pole 1 x Support Bar 1 x Hand Shank 1 x Components Collector 1 Set x Allen Keys 1x Chinese Manual | ![]() |
2.Key Features
3.Details
4.Application
How to Operate
1. Unscrew the plum twist on the feed clamp and move the feed clamp to both sides of the machine.
2. Loosen the fixing screw on the forming gear with the Allen key, and loosen the butterfly screw on the aluminum forming sheet fixing base.
3. Turn the adjusting lever of the forming sheet fixing base and move the distance between the forming sheet and the forming gear left and right to the desired size.
4. Tighten the fixing screw on the forming gear.
5. Move the adjusting lever of the aluminum forming sheet fixing base from side to side so that the distance between the forming part and the inside of the forming gear is slightly larger than the wire diameter of the part to avoid damaging the part during forming.
6. Fasten the butterfly screw.
7. Loosen the fixing screws on the cutting gear with the Allen key respectively.
8. Adjust the distance between the cutting gear and the forming gear to the desired size. Tighten the set screws on the cutting gear.
9. Place the braiding component on the hanging pole.
10. Adjust both feed clips so that the width is the same as the width of the braiding component and allow the braiding component to pass through the feed slot. Tighten the plum screw on the feed clip.
11. Place the component in the two forming gears.
12. After the above process is completed. Turn the lever at a constant speed, making the components follow the forming gears one by one and feed them into the cutting gears and circular cutter for processing, and then the forming gears and the forming sheet finish the forming process.
13. The processed parts are dropped into the container through the rewinders until all the components are processed.
Notes
1. When using this machine, please check whether all fastening screws are tightened.
2. Cutting gear, forming gear, circular cutting knife, and forming sheet are heat-treated parts, which should avoid collision with each other to produce fracture.
3. The bending gap should be adjusted according to the wire diameter of the component leads, and the standard is not to expose the copper. A slight flattening of the component lead is normal.
4. After each process, please remove the waste in time.
5. When not working for a long time, the parts should be protected with a little oil and wiped off before use.
6. Please do not bite the body of the component into the gear, which may break the gear.
7. Please add a little 40# motor oil every 3-5 days. Shaping axle, and cutting axle should always keep lubrication. Please add a little 40# motor oil every 3-5 days.
8. The distance between each part on both sides should be symmetrical when placed, otherwise, it will affect the exit material.
9. Before installation and use, please check the packing list and read the manual carefully.
10. Please note that the width of the inner diameter between the feet of the forming element is the distance between the outer diameter of the two forming gears. The length of the cutting foot of the element is the distance between the inner diameter of the two cut-off gears.
11. Please allow the slight color difference caused by the shooting light and 1-3 cm error due to manual measurement, and make sure you do not mind before ordering.
Brand | Unbranded |
---|---|
Resistance Rating | N/A |
Tolerance Rating | N/A |
Type | Resistor Forming Machine |
Termination Style | N/A |
MPN | Does Not Apply |
Manufacturer Warranty | 1 Year |
Maximum Operating Temperature | N/A |
Minimum Operating Temperature | N/A |
Power Rating | N/A |
Material | Steel |
Series | N/A |
Packaging | Box |
Country/Region of Manufacture | China |
Item Height | 17.5CM |
Item Length | 20cm |
Item Width | 20cm |
Custom Bundle | Yes |
Bundle Description | N/A |
California Prop 65 Warning | N/A |
Housing Material | Iron |
Cutter Material | Steel |
Fixing Bar Materia | Solid Steel |
Hand Shank Materia | Solid Cast Iron |
Surface Treatment | Painted |
Craftsmanship | Quenched and Forged, Hardened |
Processing Type | U Type |
Product Size: | 20*20*17.5cm/7.87*7.87*6.88in |
Hanging Pole Length | 19cm/7.48in |
Hand Shank Length | 16cm/6.29in |
Handle Length | 10cm/3.93in |
Gross Weight | 12kg/26.45lbs |
Net Weight | 10kg/22lbs |
UPC | Does not apply |