Ancel AD410 Can shut off Engine warning Light for your car .

AD310 supports to remove parts of engine lights, here are reasons cause your check engine light on include: 

1. Gas Cap 2. Oxygen Sensor 3. Air Fuel Ratio Sensor 4. Mass Air Flow Sensor 5. Ignition Coils 6. Spark Plug Wires 7. Spark Plugs 8. Thermostat 9. EGR Valve 10. Evaporatative Emission Canister Purge Valve(EVAP) 11. Catalytic Converter.

If the engine light is not turned off in time
it will Cause Serious environmental pollution , Increased fuel consumption,Increased engine noise.Increased in temperature , ect

How to verify whether the vehicle will pass the emission test with this code reader?

After entering the I/M Readiness, there will be 10 results on the list. Misfire monitor, fuel system, componentmonitor, catalyst monitor, heated catalyst, EVAP system, secondary air sys, 02 sensor, O2 sensor heater EGRand/or WVT. There will be an OK if each of them works fine. [Not all vehicles have these 10 par

Powerful Full OBD2 Functions List:

Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability

  

Supports all 12v 16pin OBD2 Car Modes

The Car Must Support OBD2 Protocol !!!
(Note: AD410 only Support 12V Gasoline& Diesel, Does not support 24V Truck )

American Car :
Need Standard OBD2 Protocols from 1996 to now
for Chrysler , for Ford, for GM, ......

European Car :
Need Standard OBD2 Protocols from 2003 to now 
For VW , for Opel , for Audi for Seat , for Peugeot , for Renault,for BMW , for Volvo....

Japanese/Korean Car:
Need Standard OBD2 Protocols from 2003 to now 
for KIA, for Isuzu, for Mitsubishi, for Hyundai , for Mazda, for Nissan, for Toyota...

Chinese Car: 
Need Standard OBD2 Protocols from 2009 to now 

Russian Car: from 2012 to now
for GAZ, for VAZ ,for LADA, for IZH, for PAZ,for SeAZ ,for UAZ, for ZAZ...

NOTE: Even though it compatible with most cars, but different regions support the vehicle OBD2 protocol at different times, or some car is spercial design, so it may not compatible with some cars which do not support OBD2 protocol.

Support OBD2 protocols car:

1.SAE J1850 PWM(41.6Kbaud)
2.SAE J1850 VPW(10.4Kbaud)
3.ISO9141-2(5 baud init,10.4Kbaud)
4.ISO14230-4 KWP(5 baud init,10.4 Kbaud)
5.ISO14230-4 KWP(fast init,10.4 Kbaud)
6.ISO15765-4 CAN(11bit ID,500 Kbaud)
7.ISO15765-4 CAN(29bit ID,500 Kbaud)
8.ISO15765-4 CAN(11bit ID,250 Kbaud)
9.ISO15765-4 CAN(29bit ID,250 Kbaud)

Mult-Languages
English,French,Spanish,German,Russian,Italian,Portuguese,Finnish,Dutch,Polish