Also available in other custom anodized colors. Just contact me if interested.
FREE WORLDWIDE DELIVERY INCLUDED !!!
Up for sale is a ...
Custom 11 Piece BRONZE Anodized Titanium Torx Screw Set
to fit Spyderco Yojimbo 2 Series Knives.
The factory standard torx screws are not titanium.
They might get rounded, threaded or simply get lost over time.
Upgrade the standard torx screws, to a set of rust proof Custom Titanium Torx Screws anodized in BRONZE.
These Custom Titanium Torx screws are a direct replacement for the Spyderco Yojimbo 2 knives.
These custom parts are not designed to fit Cloned or Fake Spyderco knives.
Do not buy these parts for any cloned or fake knives as they probably won't fit.
Might also not fit aftermarket scales if they are not the same dimensions as the factory scales.
If needing longer pocket clip screws for a thicker pocket clip or thicker scales. (Contact me for options)
Please note: No knives pictured are for sale.
What is included in this sale is only the 11 piece set of Titanium Screws to fit the Original
Spyderco Yojimbo 2 knife. Consisting of only 11 x BRONZE Anodized screws in total.
This 11 Piece set includes the following titanium screws:
2 x T10 Torx BRONZE Titanium Pivot Screws
6 x T8 Torx BRONZE Titanium Body Screws
3 x T6 Torx BRONZE Titanium Pocket Clip Screws
DECEMBER 2018 UPDATE:
WAS OUT OF STOCK DUE TO SELLING OUT.
THEN DECIDED TO RE-DESIGN THE SET AGAIN TO BE STRONGER.
POCKET CLIP SCREWS ARE NOW UPGRADED AND NOW STRONGER!!!
Many wasted parts, lots of wasted tooling, much headaches.
These custom Spyderco parts have taken around 7 Generations and at least 4 years to get it to this stage.
JULY 2018 UPDATE:
WAS OUT OF STOCK DUE TO BEING RE-DESIGNED.
PIVOT SCREWS ARE NOW STRONGER!!!
Many wasted parts, lots of wasted tooling, much headaches.
These custom Spyderco parts have taken around 6 Generations and at least 3+ years to get it to this stage.
Previous updates...below.
Please note: These custom screws were extremely hard to make.
It took many production runs and a very long time to get it to this stage.
This is as good as I can get it, as it is very hard to hold when machining
because of the thin angled edge on the countersunk screw head.
Please be aware that the screw's head may stick out from the scale
by a very, very tiny little amount. As shown in the ebay photos attached.
The G10 scale can be possibly countersunk a little be more to fix this.
However by purchasing this set you are aware of this. (2018 UPDATE = NOW FIXED)
2018 UPDATE: These are now perfect!!!
Many wasted parts, lots of wasted tooling, much headaches.
It has taken around 5 Generations and at least 3 years to get it to this stage.
2017 UPDATE: These screws were machined to fit perfectly with every allowable tolerance however it was a bit too thin
and caused it to break when torqued down hard. Had to scrap them and re-design. (2018 UPDATE = NOW FIXED)
2016 UPDATE: The scale screw's Torx drive head wasn't machined well.
Which was very hard to do on such a small thin countersunk head = looked crap. (2018 UPDATE = NOW FIXED)
2015 UPDATE: So many trial runs and bad batches. (didn't even list it up on ebay).
Many issues to sort out. (2018 UPDATE = NOW FIXED)
2014 UPDATE: Too many issues to list and remember.
Much wasted $$$$$ on tooling that didn't work. (2018 UPDATE = NOW FIXED)
Installation Notes:
The Yojimbo 2 knife can be quite tricky to take apart and put together compared to other knives.
Please do not purchase this set if you are not confident in taking your Yojimbo 2 apart and putting it back together.
Even tuning the tightness of the Yojimbo 2 body screws can effect the pivot opening performance.
The original Yojimbo 2 screws can be quite hard to remove. Please watch some youtube videos beforehand to
see how it is done. The factory loctite thread glue can make the screws hard to get out too causing the Torx head to strip.
Before installation of these titanium screws. Please clean and remove all existing factory loctite glue.
Also use some Good strong quality Torx tools to (Such as Wiha Torx tools).
Other Notes:
(This set is also available in other colors: Brass/Bronze/Purple/Blue/Raw etc. Please contact me if interested).
Anodized Titanium Cleaning Tip:
To maintain the look of your new titanium parts.
Wipe clean with some Acetone but at the same time
be careful NOT to get Acetone on the G10 or Carbon
knife scales.
(Windex can also work too as a safer option)