Discontinued part no longer manufactured by Toyota and our supply is limited . Back ordered and price is $394.00 if available. contact us to get ETA on this part.

Read listing before purchasing the item so your questions are answered. Contact us for any question.




Replacement over drive valve with updated OS ports and seals for 1982 -1994  Toyota truck pickup and early 1982-1992 Toyota Van ,JDM  2 wheel drive  Automatic Transmission Overdrive Solenoid With 2 new "O" Rings
Works with following part OEM numbers
  1. Same day shipping process within lower 48 states ( No shipping to Porto Rico zip code, no exception),
2- Delivery with Registered mail in USA and signature required so make sure you or someone is at the address to receive it. The USPS will not drop the item by your door without having your signature.

3- We offer international shipping  to Canada ( No Shipping to South America or Caribbean, sign up for global shipping on ebay to get shipping).

4- For International EU,AUSSI,NZ,JAPAN,ASIA addresses, we only provide tracking up to last port of mail departure in  USA. No tracking will be provided beyond that point and  in  your country. By purchasing this item ,you agreed and you are accepting this term that YOU WILL NOT CANCEL PAYMENT under Item NOT Received or  item Not Delivered.

Technical information:
We also carry this part for model listed below in our other ebay listing
  • Build with heavy duty 3 feet cable
  • Requires using your old wire and plug to attach to new Overdrive Solenoid with butt connector (provided in this kit).
  • Direct fit with 2 set of new  "O" Rings included
  • Easy installation and email support ( clean /brush/wash the solenoid area before pulling your old one out)
To Request  Return,YOU MUST FOLLOW THE TERMS listed here:


1-“Items must be returned in original non-open condition unused ,  within 7 days  from date of purchase. 2- return item as new as you received  in the original packing / box with seals .3-Not used or installed. 4-Installation  of this part on the vehicle  will void return.No exception.
5-By holding this item in your position for more than 7 days after purchase /delivery date, you agreed with sale's term, absolutely we will not honer return and will decline return and charge-back with your financial institution.



ATF transmission oil Must be change when this valve is replaced. failure to change ATF oil will allow particles and contamination from transmission to block ports and cause  leak from upper boot part of the seal where cable is attached which it will voids return and  warranty. Read and follow this instruction to avoid costly replacement.


  • Make sure you return item within 7 days to speed up your refund process with new  O rings you received and do not ship it with without O-Rings or your old O-Rings
  • Part Distributor will not exchange this item if it is shipped with old O-rings
  • Top black cover of the solenoid  must be unopened or not broken or glued or repaired
  • Do not  try to ship your OLD one to get refund, we will report you to EBAY
To install follow instruction below:

1- clean the area where old valve is mounted before removing the old overdrive valve. clean the back where (2)  mounting bolts are
2-wash the back and front of the valve area with carburetor cleaner/brake cleaner etc. blow air if possible to clean the dirt
3-Remove the old valve facing up.
4-Do not clean the area after the old valve is removed. Dirt will fall in to transmission port causing damages to transmission.
5-install new valve with O-rings already installed on the valve. DO not place the o-rings on the transmission side first
6-Mount two bolts and torque them to 10 ft lb.
7-Connect cable to your old cable connector with butt connector provided and crimp it.Roll black tape over the connector to prevent water or moisture onto wiring harness .
8-Start the engine in park  and check for ATF leaks around the valve lower seals and upper cable cover seal for up to 3 minutes
9- Darin  old ATF fluid from pan and fill the transmission with new ATF fluid