Tron Leg Set
This listing is for:
1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn or Quorra
2) Two pieces of shaped and angled EL Tape to go round the knees
3) Two pieces of 'Sacral 'shaped EL Panels to be placed at the lower back
4) Two pieces of 2cm x 25cm EL Tapes
4) A Powerful 8xAA battery EL Driver
4a) choice of power source for this Driver:
I) Standard 8xAA Battery Box
II) Rechargeable Li-ion Battery (smaller and lighter) with Intelligent Charger (Li-ion Batteries are only available in the UK due to airmail postal restrictions)
5) A 2 Way Splitter, 3 Way Splitter and 2 x 'Short, Medium and Long' Splitters
6) 1.5 metres of hook & loop tape - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable for washing.
Orange or Light Blue
Dimensions of the products:
If you are making a costume, it is a good idea to plan it out properly.
For this set, the Driver/Inverter is very powerful and comes with a separate power pack
So here are the dimensions of all the parts plus lengths of wire between them:
THE POWER PACK
Takes 8xAA batteries (not supplied) and is 12.7cm x 7.2cm x 1.9cm
It has a 21cm thin power wire coming out of it that leads to the...
DRIVER
The Driver is 6cm x 4cm x 4cm
It has the controls on it - Off, Flashing or On
It has a 55cm wire coming out of it that leads to the...
SPLITTER
The Splitter is 40cm long in total, it is 20cm of wire which then splits into separate strands which are all 20cm long.
A 3 Way Splitter attaches to the Driver
One of these channels has a 2 Way Splitter attached that runs round the back to plug into the pair of EL Sacral pieces
The other two channels have a special '3 way (Small Medium and Long) Splitter attached to them that run down each leg
These SML Splitters have:
one 'Short' channel that plugs to the 25cm Tape.
Then the 'Medium' channel plugs into the Knee Joint section
The 'Long' channel goes down to the Shin to plug into the Double Hoop
The three pieces of EL Tape that run down the leg are:
1) SHIN
This 15cm Double Hoop is designed to run from your shin to the ankle to give a great finishing touch to any Tron costume (these are also available for other parts of your Tron costume in our ebay shop)
2) KNEE JOINT
Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes
This has been made to largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you
That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)
3) 2cm x 25cm EL Tape
Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume
Coming from the 2 Way Splitter at the back of the costume:
3) EL SACRAL
This pair of Panels sit at the base of the spine and look pretty awesome!
The Tape is just 350 microns thick - that is 1/3rd of a millimetre!
Sticky back hook & loop tape is supplied that is the exact width of the EL Tape.
You must sew the other part of the hook & loop tape onto the costume making it very convenient to attach and remove
Of course, you don't need to use the hook & loop tape, fix it any way you choose
Please feel free to message us if you have any questions or would like planning your set.
The whole kit is ready to use - just plug and play!
A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from our ebay store
VISIT OUR SHOP TO SEE OUR RANGE OF INVERTER/DRIVERS, SPLITTERS AND OTHER EL WIRE