Available in heat transfer vinyl HTV, permanent adhesive (sign) craft vinyl & reusable, no residue, removable adhesive vinyl & decal
Tons of patterns & options! Contact us if you'd like to make a special request or custom pattern!
Professionally Printed Pattern Vinyl
for
HTV & Craft Vinyl
High-quality pattern vinyl
3 Options to choose from:
Siser Colorprint Easy Iron On Heat Transfer Vinyl
Patterned Oracal 651 Glossy Permanent Adhesive Craft Vinyl
Reusable No Residue Removable Adhesive Vinyl
Permanent Adhesive Craft Vinyl (Outdoor/Indoor Vinyl)
Printable Oracal 651 - No Transfer Tape Provided
- Great to use on glass, metal, plastic, and much more! Please clean surface before use!
- Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a
transfer tape to transfer design off of the backing and place on your smooth & clean surface - Weatherproof / 4+ years durability
Reusable No Residue Non-Slip Removable Adhesive Craft Vinyl (Outdoor/Indoor Vinyl)
Apply, Remove & Apply Again! No Residue when peeling!
Comparable to 3M - No Transfer Tape Provided
- Great to use on glass, metal, plastic, and much more! Please clean surface before use!
- Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply a
transfer tape to transfer design off of the backing and place on your smooth & clean surface - Weatherproof / 7+ years durability
Iron on Heat Transfer Vinyl - For Any Garment or Fabric
Printed on Siser ColorPrint Easy (TTD High-Tack Mask Provided)
- Heat Transfer is printed without the carrier. Siser TTD Easy Mask is provided
for application - Cut on Pattern Side and DO NOT MIRROR. After weeding excess vinyl, apply
TTD Easy Mask to transfer design off of the backing and place on your garment face up - Can be applied with a home iron and/or heat press
| CUTTER SETTINGS | |||
| Cricut: Blade: Standard Setting: Iron On | Silhouette Cameo: Blade: Standard, 3 Material: Heat Transfer, Smooth Speed: 8 Force: 6 | Scan N Cut: Blade: Standard, 2 Cut Speed: 1 Cut Pressure: 1 | |
| Roland GS/GX-24: Blade: 45° Gram Force: 80-90 Offset: 250 Speed: 25-50 cm/s | Graphtec: Blade: 45° Gram Force: 9 Tool: CB09U+0 Speed: 25 cm/s | MH, SC2, LP3, & Titan 1: Blade: 45°/60° Gram Force: 80-85 Speed: 300mm/s *Blade Advancing Varies | Titan 2 & 3 Blade: 45°/60° Gram Force: 60-65 Speed: 300mm/s *Blade Advancing Varies |
| Settings may vary based on blade condition and age of machine. Always perform a test cut prior to cutting designs. | |||
| APPLICATION INSTRUCTIONS | |
| Application Instructions (home iron) Set iron dial between Cotton and Linen Cover design with Kraft paper or non-stick cover sheet Place on flat, hard surface (ironing board not recommended) Press iron with medium/firm pressure (do not slide iron) Press each section of design for 15 seconds If areas of design lift after application, replace cover sheet and re-press for 10 seconds Peel carrier hot or cold | Application Instructions (heat press) Cut material - don't mirror! Weed excess material Mask with TTD High Tack Mask Preheat garment for 2-3 seconds Apply design at 305°F/150°C Use medium pressure for 10-15 seconds Peel carrier hot or cold Cover and reheat for 2-3 seconds |
| RECOMMENDED ACCESSORIES & CARE | |||
| Patterned Vinyls Apply to: 100% cotton Poly/cotton blends 100% polyester Leather Lycra®/spandex | Recommended Accessories: Weeder/Tweezers | Laundering: Wait 24 hours before 1st wash Machine wash cold / mild detergent Dry on normal dryer setting Do not dry clean Do not bleach | |
| SIZE AND HOW TO APPLY | |
 | 1) Do not mirror 2) Cut on pattern 3) Weed excess vinyl 4) Apply and peel mask 5) Press |
 | 1) Do not mirror 2) Cut on pattern 3) Weed excess vinyl 4) Apply and peel mask |
| CUSTOM PATTERNS AND DESIGNS |
| Have your own patterns you want to print? Contact us today! |