PL2303HX Brush Cable+PL2303TA Download Cable

Parameter:

  • Product Name: USB to TTL download line

  • Length: 1 meter

  • Chip: PL2303HX, PL2303TA,

  • Line order definition (Red +5V,Black GND,Green TXD,White RXD)

Description:


         Please do not directly get the operation, first do a simple test, the method is very simple: If you plug the line into the computer, the computer prompts "find new hardware....", connect with a black pen (GND) The red pen can be connected to both (RX) and (TX) to measure the voltage, which means the small board must be good. Here, it is specially stated that if (GND) is connected to the voltage pin of the device, the power-on must be burned, so the pin of the device must be accurately measured before wiring.


Pin connection and description:


        Please be sure to find the pin definition before connecting, especially the GND must not be connected to the voltage pin, and the RX and TX terminals should not be connected to the VCC pin. (The actual VCC pin voltage is up to 14V.) Will burn the patch chip,


         Connection method: only 3 wires are needed for the brushing machine. Generally, only three signal lines of RX TX GND are used, and VCC is not connected. Above is a 4, 5 pin friend, do not need to connect VCC and BT pin. When using, please connect RXD with target board TX, TXD is connected with target board RX, GND is connected to GND, if not, adjust RX and TX.


Connection method:

RX to TX;

TX to RX;

Ground to ground (GND to GND)



  • Red  VCC

  • Black GND

  • White RXD

  • Green TXD


USB to serial port small board function:


1 Simple serial communication.

2 router or ADSL firmware upgrade.

3 GPS serial communication.

4 Hard disk firmware upgrade.

5 Easy to use, RX is connected to the TX of the MCU; TX is connected to the RX of the MCU. There is no need to convert with MAX232.

6 used in the HyperTerminal; commonly used serial debugging tools.

7 Various satellite machines are upgraded.

ect...............Universal USB to serial portlet


New PL2303TA Download Cable

       This is a completely new product, using the PL2303TA chip, the PL2303TA provides a convenient solution for connecting a RS232-like full-duplex asynchronous serial device to any universal serial bus (USB) host. The PL2303TA is perfectly compatible with the win XP/VISTA/7/8/8.1 system and can emulate the existing applications that allow COM-based ports on most operating systems to easily port and perform USB connectivity without the need to rewrite the COM port software. Apply traditional COM ports.
        By utilizing the advantages of USB bulk transfer mode, large data buffer and automatic flow control, the PL2303TA can achieve higher throughput than the traditional UART does not require (universal asynchronous transceiver) true RS232 signal, the transmission rate is higher than 115200 The base point can be used for even higher performance. The PL2303TA's flexible baud rate generator can be programmed to produce any rate between 75 base points and 6 million base points.
       The PL2303TA is designed for mobile and embedded solutions and offers a compact and easily adaptable to any connector and handheld device. With the operating or suspend mode being very power hungry, the PL2303TA is the perfect power-filled left-to-connect device bus-powered operation.
       This product is specifically for laboratories, product testing, low-cost MCU communication and other applications, there are 4 lead lines

  • Red +5V

  • Black GND

  • White RXD

  • Green TXD

Applications:

  • Single-chip solution upgrade for traditional RS232 device to USB interface

  • USB to RS232 converter / cable / dongle

  • Health/medical USB interface data transmission line

  • USB interface for personal infotainment/media player docking

  • USB interface data transmission line for mobile phone/handheld computer

  • Serial-over-IP wireless solution

  • USB barcode / smart card reader

  • GPS / Navigation USB Interface

  • Point of sale terminal (POS) terminal/printer

  • Computer docking station / port replicator

  • Industrial / Instrumentation / Automation Control USB Interface

  • USB Modem / Wireless / Zigbee USB Interface

  • Set-top box (STB) / home gateway USB interface

  • BatteryCharger application

  • USB interface of MCU-based devices






USB to RS232 TTL PL2303HX Module USB Download Converter Module
Remark
There are different colors of boards, will be sent randomly.
Single-chip programming, medium 9 upgrade, hard disk repair, routing upgrades, etc. preferred.
the new original CH340G chip, this series of chips is the official USB-to-TTL chip recommended by STC, there will be no incompatibility caused by different drivers / different computers! ! !
not only the power lamp PWR, but also TXD and RXD indicators, easy to understand whether the product is working without the instrument;
support WINDOWS 98/ME/2000/XP/Server 2003/VISTA/Server 2008/Win7/Win8/win10 32-bit/64-bit
module size: 55mm * 16mm,
PCB size: 33mm * 16mm;





DataCaciques