5V 1Channel

 

Module description:

1. the module uses genuine quality relay, normally open interfaces Maximum load: AC 250V/10A, DC 30V/10A;
2. using SMD optocoupler isolation, driving ability, stable performance; trigger current 5mA;
3. the module Operating voltage 5V;
4. the module can be high or low by a jumper setting trigger;
5. fault-tolerant design, even if the control line is broken, the relay will not operate;
6. the power indicator (green), the relay status indicator (red)
7. the interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient
8. module size: 50mm*26mm*18.5mm (L*W*H)

Module interface:

1. DC+: positive power supply (VCC)
2. DC-: negative power supply (GND)
3. IN: can be high or low level control relay

 

Relay outputs:

1. NO: normally open relay interface
2. COM: Common Interface Relays
3. NC: normally closed relay interface

 

High and low level trigger options:

It is low level trigger when jumper connect to LOW pin

It is high level trigger when jumper connect to HIGH pin

 

 

 

5V 2Channel

 

Module description:

1. Maximum load on normally open pin: AC 250V/10A, DC 30V/10A.
2. Trigger current 5mA;
3. Module can be set high level or low level trigger by jumper wire;
4. Power indicator light (green), relay status indicator light (red);
5. Module size: 50mm*41mm*18.5mm.

 

Module interface specifications:

1. DC+ : DC power supply positive pole
2. DC- : DC power supply negative pole
3. IN1 : channel 1 signal triggering pin
4. IN2 : channel 2 signal triggering pin

 

Relay output:

1. Normally closed pin (NC1) : channel 1 relay normally closed pin
2. Common pin (COM1) : channel 1 relay common pin
3. Normally opened pin (NO1) : channel 1 relay normally opened pin
4. Normally closed pin (NC2) : channel 2 relay normally closed pin
5. Common pin (COM2) : channel 2 relay common pin
6. Normally opened pin (NO2) : channel 2 relay normally opened pin

 

High or low level trigger option:

1. S1:It is option switch for channel 1 relay;
2. S2:It is option switch for channel 2 relay;
3. It is low level triger if COM pin connect to LOW pin; It is high level triger if COM connect to High.

 

 

 

5V 4Channel

 

Module description:

1. Maximum load on normally open pin: AC 250V/10A, DC 30V/10A.
2. Trigger current 5mA;
3. Module can be set high level or low level trigger by jumper wire;
4. Power indicator light (green), relay status indicator light (red);
5. Module size: 73mm * 50mm* 18.5mm.

 

Module interface specifications:

1. DC+ : DC power supply positive pole
2. DC- : DC power supply negative pole
3. IN1~IN4 : relay signal triggering pin

 

Relay output:

1. Normally closed pin (NC1~NC4) : relay normally closed pin
2. Common pin (COM1~COM4) : relay common pin
3. Normally opened pin (NO1~NO4) : relay normally opened pin

 

High or low level trigger option:

1. S1~S4:They are option switch for relay 1~4;
2. It is low level triger if COM pin connect to LOW pin; It is high level triger if COM connect to High.

 

 

9V 1Channel

Module description:

1. the module uses genuine quality relay, normally open interfaces Maximum load: AC 250V/10A, DC 30V/10A;
2. using SMD optocoupler isolation, driving ability, stable performance; trigger current 5mA;
3. the module Operating voltage 9V;
4. the module can be high or low by a jumper setting trigger;
5. fault-tolerant design, even if the control line is broken, the relay will not operate;
6. the power indicator (green), the relay status indicator (red)
7. the interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient
8. module size: 50mm*26mm*18.5mm (L*W*H)

Module interface:

1. DC+: positive power supply (VCC)
2. DC-: negative power supply (GND)
3. IN: can be high or low level control relay

 

Relay outputs:

1. NO: normally open relay interface
2. COM: Common Interface Relays
3. NC: normally closed relay interface

 

High and low level trigger options:

It is low level trigger when jumper connect to LOW pin

It is high level trigger when jumper connect to HIGH pin

 

 

 

9V 2 Channel

 

Product Name: Optocoupler Driver Relay Module

Relay Type: SRD-09VDC-SL-C

Coil Voltage: DC 9V

Pole Number: 2 Channel

Load: 10A, AC 250V/125V, DC 30V/28V

Overall Size: 5 x 4.1 x 1.8cm/2" x 1.6" x 0.7"(L*W*H)

Materials Meta: Plastic, Electric Parts

Main Color: Red

 

 

 

9V 4 Channel

 

Product Name: Optocoupler Driver Relay Module

Relay Type: SRD-09VDC-SL-C

Coil Voltage: DC 9V

Pole Number: 4 Channel

Load: 10A, AC 250V/125V, DC 30V/28V

Overall Size: 7.3 x 5 x 1.8cm/2.9" x 2" x 0.7"(L*W*H)

Materials Metal: Plastic, Electric Parts

Main Color: Red

 

 

 

12V 1 Channel

 

module size: 50mm * 26mm * 18.5mm (L * W * H)

four mounting bolts holes, hole 3.1mm, 44.5mm * 20.5mm pitch

Two module interface:

1, DC +: positive power supply (voltage required by the relay, there 5V.9V.12V and 24V choice)

2, DC-: negative power connection

3, IN: can be high or low level control relay

Relay outputs:

1, NO: normally open relay interface, the relay before the vacant after the pull shorted with COM

2, COM: Common Interface Relays

3, NC: normally closed relay interface relay shorted with COM ago, after the pull-vacant

High and low level trigger selection ends:

1 when jumper short circuit with LOW is low lever trigger;

2 When jumper short circuit with high is high lever trigger.

 

 

 

12V 2 Channel

 

Module size: 50mm*41mm*18.5mm.

Module interface specifications:

1. DC+ : DC power supply positive pole
2. DC- : DC power supply negative pole
3. IN1 : channel 1 signal triggering pin
4. IN2 : channel 2 signal triggering pin

Relay output:

1. Normally closed pin (NC1) : channel 1 relay normally closed pin
2. Common pin (COM1) : channel 1 relay common pin
3. Normally opened pin (NO1) : channel 1 relay normally opened pin
4. Normally closed pin (NC2) : channel 2 relay normally closed pin
5. Common pin (COM2) : channel 2 relay common pin
6. Normally opened pin (NO2) : channel 2 relay normally opened pin

 

 

 

12V 4 Channel

 

Size: 73mm * 50mm * 18.5mm ( L * W * H )

four mounting bolts holes , hole 3.1mm, 67mm * 44.5mm pitch

Interface :

1. DC +: positive power supply ( voltage required by the relay , there 5V.9V.12V and 24V choice )
2. DC-: negative power connection
3. IN1-IN4: each way based on the settings , can be high or low to control the corresponding relay

outputs :

a 12- line interface, the interface can be directly connected to all leads , user-friendly

1. NO1 - NO4: normally open relay interfaces , relay before the vacant after the pull shorted with COM
2. COM1 - COM4 Common Interface Relays
3. NC1 - NC4: normally closed relay interface relay shorted with COM ago , after the pull- vacant

 

 

 

24V 1Channel

 

Description

1. ?NO? Pin Maximum load: AC 250V/10A, DC 30V/10A
2. Using SMD OPTOCOUPLER isolation, the trigger current only 5mA
3. The module have 5V, 9V, 12V and 24V are available
4. The module can be set to high or low triggered by jumper
5. Fault-tolerant design, even if the control line is broken, the relay will maintain;
6. Has the power indicator (green) and relay status indicator (red)
7. Size: 50*26*18.5mm
8. Has four mounting bolts holes, hole 3.1mm, 44.5*20.5mm pitch

Interface:

Input:

VCC: Relay power supply +

GND: Relay power supply -

IN: Signal trigger input (High or Low Level Signal, select via jumper)

Output:

NO: Relay normally open.

COM: Relay Common Pin

NC: Relay normally closed.

High or Low Level Trigger Select:

1. Use High Level Trigger

When ?IN? input High Level Signal, the ?NO? connect with ?COM?

When ?IN? input Low Level Signal, the ?NC? connect with ?COM?

2. Use Low Level Trigger

When ?IN? input Low Level Signal, the ?NO? connect with ?COM?

When ?IN? input High Level Signal, the ?NC? connect with ?COM?

3. High or Low Level Trigger Select

Jumper connect with L, Low Level Trigger

Jumper connect with H, High Level Trigger

 

 

 

24V 2 Channel

 

Module size : 50mm * 41mm * 18.5mm ( L * W * H )

four mounting bolts holes , hole 3.1mm, 44.5mm * 35.5mm pitch

Interface :

1. DC +: positive power supply ( voltage required by the relay , there 5V.9V.12V and 24V choice )
2. DC-: negative power connection
3. IN1: 1 channel signal to trigger the end , you can set a high or low level control relay
4. IN2: 2 -channel signal to trigger the end , you can set a high or low level control relay

Outputs :

1. NO1: After a relay normally open interfaces , relay before floating, shorted pull with COM1
2. COM1: 1 relay common interface
3. NC1: 1 relay normally closed port, COM1 relay shorted before and after the pull- vacant
4. NO2: 2 -way normally open relay interface, the relay before floating , pull back and COM2 short
5. COM2: 2 Common Interface relay
6. NC2: 2 -way normally closed relay interface relay short front and COM2 , pull vacant post

 

 

 

24V 4 Channel

 

Module size : 73mm * 50mm * 18.5mm ( L * W * H )

four mounting bolts holes , hole 3.1mm, 67mm * 44.5mm pitch

Interface :

1. DC +: positive power supply ( voltage required by the relay has 24V option)
2. DC-: negative power connection
3. IN1-IN4: each way based on the settings , can be high or low to control the corresponding relay

Outputs :

12- line interface, the interface can be directly connected to all leads , user-friendly

1. NO1 - NO4: normally open relay interfaces , relay before the vacant after the pull horted with COM
2. COM1 - COM4 Common Interface Relays
3. NC1 - NC4: normally closed relay interface relay shorted with COM ago , after the pull- vacant

 

 

 

5V 30A 1Channel

 

Specifications:

 

The item is a 5V 1-Channel Relay interface board,It can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on.

1-Channel Relay interface board,

Equiped with high-current relay : DC 30V AC250V 30A

Standard interface that can be controlled directly by microcontroller (Arduino , 8051, AVR, PIC, DSP, ARM )

Size:47*36 mm

 

 

 

12V 30A 1Channel

 

30A relay module, normally open interface maximum load: AC 250V/30A, DV 30V/30A

Optical coupling isolation, driving ability is strong, stable performance;Trigger current is 5mA

Module can be set high level or low level trigger by the jumper

Power indicator light (green), relay status indicator light (red)

Module Size:50mm*33mm*24mm

　

Technical parameters:

Voltage version:12V

The static current:5mA

Working current:80mA

Trigger current:2-4mA

　

Module interface specifications:

DC+ : DC power supply positive pole

DC- :DC power supply negative pole

IN : signal triggering pin

JD+ : relay control voltage positive

JD- : relay control voltage negative

DC+ and JD+ shorted by jumper cap, DC- and JD- shorted with jumper cap, it is the same voltage between trigger terminal and relay control terminal

High and low level trigger mode selection.Jumper and L pin connection, IN pin is low level triggerJumper and H pin connection, IN pin is high level trigger

Normally closed pin (NC) : relay normally closed pin

Common pin (COM) : relay common pin

Normally opened pin (NO) : relay normally opened pin

 

 

 

24V 30A 1Channel

 

Description:

30A relay module, normally open interface maximum load: AC 250V/30A, DV 30V/30A

Optical coupling isolation, driving ability is strong, stable performance;Trigger current is 5mA

Module can be set high level or low level trigger by the jumper

Power indicator light (green), relay status indicator light (red)

Module Size:50mm*33mm*24mm

　

Technical parameters:

Voltage version:24V

The static current:5mA

Working current:50mA

Trigger current:2-4mA

　

Module interface specifications:

DC+ : DC power supply positive pole

DC- :DC power supply negative pole

IN : signal triggering pin

JD+ : relay control voltage positive

JD- : relay control voltage negative

DC+ and JD+ shorted by jumper cap, DC- and JD- shorted with jumper cap, it is the same voltage between trigger terminal and relay control terminal

High and low level trigger mode selection.Jumper and L pin connection, IN pin is low level triggerJumper and H pin connection, IN pin is high level trigger

Normally closed pin (NC) : relay normally closed pin

Common pin (COM) : relay common pin

Normally opened pin (NO) : relay normally opened pin

 

 

 

Package Include:

1 x Relay Module