eBay

150W

1. Featrure:

1). Module Properties: non-isolated step-up module (BOOST)

2). Input voltage: 10-32V

3). Output voltage: 12-35V (adjustable)

4). Output Current: 10A (MAX)

5). Input Current: 16A (MAX) (Please enhance heat dissipation if more than 10A)

6). Output power: natural cooling 100W (MAX), enhance heat dissipation 150W (MAX)

7). Easy to drive 65W 90W dual-core notebook.

8). Use a 12V battery drive 19V 3.42A notebook, the module temperature about 45 Celsius

9). Conversion efficiency: 94% (measured at Input 16V, output 19V 2.5A) (For reference)

10). Output Ripple: 2% (MAX) 20M-bandwidth

11). Operating Temperature: Industrial (-40 Celsius to +85 Celsius) (ambient temperature exceeds 40 Celsius, lower power use, or to enhance heat dissipation)

12). Full load temperature rise: 45°c

13). No-load current: 25mA typical

14). Voltage regulation: ± 0.5

15). Load Regulation: ± 0.5%

16). Dynamic response speed: 5% 200uS

17). Size: 65mm x 47mm x 23.5mm

18). Short circuit protection: None (Please Install fuses and protection circuits at Input port.)

19). Input Reverse Polarity Protection: None (Please Series diode at the input port.)

2. Applications:

( 1 ). DIY an output adjustable vehicle power supply, connect the 12V input, and output could be 14-35V (adjustable freely), However, the output voltage can not be less than the input voltage.

( 2 ). Car laptop power supply: connected to 12V power supply, output voltage regulation as your notebook need.

( 3 ). Boost charger. You can use the 12V power supply to charge battery more than 12V, for example, 24V battery.

300W

Features:

Use a dedicated benchmark IC, and high-precision current sensing resistor, make more stable constant current, (when 20°C to 60°C constant current 5A, temperature drift less than 5%). suitable for LED driver.
Fixed turn lamp current is 0.1 times the current value (When charging, used to identify whether the battery is fully charged);
High output current, the max output current can reach 8A.
Low output ripple , high frequency capacitor reduces output ripple.

Module parameters:

Module Properties: non-isolated step-down module, constant current and constant voltage module (CC CV), charging module
Input voltage: 7-40V
Output voltage: 1.2-35V (continuously adjustable)
Output Current: 8A Max ( power tube temperature exceeds 65°C please add cooling fan )
Constant current range :0.2-8A ( adjustable )
Turn lamp current : constant current value * ( 0.1 ) , turn lamp current and constant current value linkage.For example, constant current value 3A, turn lamp current is set to 0.1 times constant current(0.1 * 3A = 0.3A). When adjust the constant current to 2A , then turn lamp current is 0.1 times constant current (0.1 * 2A = 0.2A).
Turn lamp current is fixed to 0.1 time in this version( actually turn lamp current value is probably not very accurate ), it is for identify whether the battery is fully charged.
Dropout voltage: 1V
Output Power: Maximum power is about 300W, power tube temperature exceeds 65 degrees please add fan.
Conversion efficiency : up to approximately 95% ( the higher output voltage, the higher the efficiency )
Operating frequency: 180KHZ
Output ripple : 20M bandwidth ( for reference only )
Input 24V Output 12V 5A ripple around 50mV ( excluding noise )
Operating temperature : Industrial grade (-40 °C to +85 °C)
No-load current : Typical 20mA (24V step down to 12V)
Load regulation : ± 1% ( constant voltage)
Voltage regulation : ± 1%
Constant accuracy and temperature: actual test , the module temperature changes from 25 degrees to 60 degrees , the change of the constant current value is less than 5% ( constant current value 5A)
Dynamic response speed : 5% 200uS
Potentiometer adjustment: clockwise ( increase ) , counterclockwise ( decrease ). The potentiometer close to the input port is for voltage adjust (CV), the potentiometer close to the output port is for current adjust(CC).
Indicator : double color indicator. When charging the indicator is RED, fully charged is GREEN( No load is green ).
Output short circuit protection : Yes , constant current ( constant current value you set)
Input Reverse Polarity Protection: None
Output prevent backflow : None.
Wiring: Terminal
Size:65(L)*47(W)*23.5(H) mm

Applications:

High-power LED constant current drive ,
Lithium battery(or Iron battery) charge,
6V, 12V, 14V, 24V battery charge ,
Nickel-cadmium nickel-metal hydride battery ( battery pack ) charge ,
Solar panels and wind turbines

Battery charge:

Make sure of the battery float voltage and charging current that you need, the input voltage of the module.
Adjust the constant voltage potentiometer, adjust the output voltage to about 5V.
Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected charging current value.
Adjust the constant voltage potentiometer make the output voltage reaches the float voltage;
Connected to the battery, try to charge.

(1,2,3,4 steps to connect the power module input, output no-load does not connect battery.)

LED constant current drive:

Make sure operating current and Max operating Voltage of the LED you need to drive.
Adjust the constant voltage potentiometer, adjust the output voltage to about 5V.
Use the multimeter in 10A current scale to measure output short-circuit current, and adjust the current potentiometer to make sure the output current to the expected LED operating current.
Adjust constant voltage potentiometer make the output voltage reach the maximum LED operating voltage.
Connect LED, test.

(1,2,3,4 steps to connect the power module input, output No-load does not connect LED.)

Mini Digital Voltmeter Ammeter DC 100V 10A Panel Amp Volt Voltage Current Meter Tester 0.56" Blue + Red Dual LED Display

Description:

Working voltage of Meter itself:DC 4 - 30V(The maximum input voltage can not exceed 30V. Otherwise the meter will be burned)

Working current of Meter itself:≤20mA
Voltage Measuring range: DC 0 - 100V
Current Measuring range: DC 0 - 10A
Voltage resolution (V): 0.1V
Current resolution (A): 0.01A
Measure accuracy: 1% (± 1 digit)
Display: 0.28" digital tube, Two color blue and red
Refresh rate: about 300mS / times
Dimensions:48mm*29mm*26mm
Operation Temp: -10°-+65°