Product Information:


ECU tune required

PRL-HCR-INT-HVI-B - PRL Motorsports RACE High Volume Air Intake System - Honda Civic Type-R FK8 (2017-2021)

 

PRL Motorsports High Volume Intake Logo

 

INSTALLATION:

PDF - 2017-2021 Honda Civic Type-R High Volume Intake System Install Instructions PDF Document Icon

 

Patent No. D902,255

Important Notes:

  • NO ECU CALIBRATION REQUIRED FOR STANDARD BORE MAF HOUSING
  • BIG BORE MAF-SPECIFIC ECU CALIBRATION IS REQUIRED FOR BIG BORE MAF HOUSING

 

Technical Notes:

Our FK8 Civic Type-R High Volume Intake system utilizes a 6" cone filter and 2-piece MAF housing with velocity stack(s) to allow maximum airflow while delivering proper fuel trims. The HDPE rotomolded air box utilizes the factory air duct and seal for optimal airflow and heat-soak reduction. Custom molded 4-ply silicone allows for all components to be safely attached without obstructing airflow.


The Big Bore MAF housing option is the largest MAF housing on the market, rated at 600+ horsepower, and offers a 47% increase in airflow volume over the factory MAF housing or Standard Bore HVI MAF. Our engineers were able to profile the volute and locate the MAF sensor flange in the optimal location to help keep fuel trims extremely stable. This will require a calibration/MAF scaling and is more-so intended for customers looking to make over 450 horsepower.

Kit Includes:

  • (1) 4-Ply Silicone Intake Hose
  • (1) Injection Molded Evap Fitting
  • (1) Two-Piece MAF Housing
  • (1) Rotomold Air Box
  • (1) 6" Air Filter
  • (4) Stainless Steel Breeze Lined Clamps
  • Stainless hardware
  • Wire Loom
  • Dress-Up Hardware Kit

Testing Data:

All testing was performed on the same day with a rather mild 55 degree Fahrenheit day and moderate humidity. We started all single dyno pulls at 174 degrees, while continuous (back-to-back) dyno pulls start at 174 degrees and end around 197 degrees. For our first comparison we tested the factory intake system on KTuner's stock equivalent ECU map versus our High Volume Intake System on KTuner's stock equivalent ECU map for an apples-to-apples comparison. Run 2 was the coolest (174 degree starting temp) for both setups. We saw an 11 - 12 horsepower peak gain and 32 horsepower gain throughout the mid-range over the factory intake system.

Continuous dyno pulls and testing under the same conditions produce identical gains time after time. Even our hottest runs, Run 4 (197 degree starting temp), showed a 5 horsepower peak gain and 26 horsepower gain throughout the mid-range over the factory intake system.


Next, we uploaded KTuner's Stage 1 ECU map with the factory intake system and our High Volume Intake System. The coolest runs, Run 2, showed an 8-9 horsepower peak gain and 25 horsepower gain throughout the mid-range.

The hottest runs, Run 5, showed a 9 horsepower peak gain and 18 horsepower gain throughout the mid-range.

One of our main focuses with this intake system was to offer a factory-like fuel trims (much like our 1.5T Cobra CAI & SRI) for optimal drivability and performance. We spent quite a bit of time designing what we determined is the best intake system/MAF housing on the market. Thus far we have seen Short Term Fuel Trims within +2-4% of the factory. We have a few more tricks up our sleeve, but are very happy and confident with what we have currently.





Application:

Fits all 2017-2021 Honda Civic Type-R FK8
Fits all variant models including RHD, International Models, Etc.
Fits Factory Turbocharger Inlet Pipe ONLY

Shipping:

We may either ship through USPS, UPS, or FedEx at our own discretion.

Products are usually shipped out Monday – Friday. Please contact us through email for assistance regarding other shipping methods.

Return policy:

When receiving your package, please open all of the boxes immediately to check if all the contents are inside and not damaged. All damaged or defective items must be reported within 2 business days from the day the packaged is delivered. If the package appears to be damaged on the outside, please refuse to accept it from the carrier; or please make sure when signing the shipper's proof-of-delivery slip, you include a note stating that the package is or appears damaged. If you do accept a damaged shipment, please inform us immediately. Depending on the product and where/how it was shipped, it may be necessary for you to deal with the carrier. 

If the product received is defective, a replacement will be sent as soon as possible. If you decide to return the defective item, rather than replace it, a restocking fee will be assessed (15-50% depending on the item) and your original shipping and processing charges will not be refunded. Also, returned products must be in its original packaging which allows us to re-sell the product. We will refuse any damaged or products that are not in good condition. 

If after 30 days of receiving your product, it proves to be defective, we would like for you to deal with the manufacturer. They will inform you on how to proceed based on their policies. 

If you are unhappy in any way, please contact us through eBay messages. We will provide you instructions on how and where to return the product.