FOR SALE

DJI F550 Hexacopter
DJI Arms
Landing Gear
DJI E300 Tuned Propulsion System 
4x DJI 920Kv Motors 
4x DJI E300 ESCs
4x E300 Quick Release Propellers 
Tarot T4 3D Camera Gimbal
DJI Naza V2 GPS Flight Controller
Lemon RX
More 
 FREE POSTAGE!


For sale is a used DJI F550 hexacopter with DJI E300 tuned propulsion system. Below is a list of parts included in the F550 build.

DJI F550 Specification:

DJI F550 frame
DJI F550 fixed landing gear
6x DJI arms 
DJI Naza V2 flight controller with GPS
DJI tuned propulsion system-
- 4x DJI E300 920Kv Motors 
- 4x DJI E300 
- DJI 15A ESCs, 
- 6x DJI 9x4 quick release propellers 
Tarot T4 3D camera gimbal to fit a GoPro or similar camera
Lemon RX receiver
5.8GHz tx with clover antenna
XT60 battery connector 

Everything shown in the pictures is included.
 
The hexacopter will need a Spektrum radio to bind with the Lemon RX receiver and 3 cell lipo battery to complete it. Below is a more detailed description of the items fitted to the hexacopter.

If you have any questions please ask. This item will be posted with Royal Mail where a signature is required on delivery. Please see my other sale items!

DJI E300 Tuned Propulsion System Description:

The DJI E300 Tuned Propulsion System for Quadcopters provides an all in one solution for the Quadcopter builders. The E300 system delivers greater aerodynamic efficiency and a higher thrust-to-weight ratio from the 9x4 propellers, while increasing reliability, stability and agility and is compatible with multi-rotor platforms. The E300 kit is suppled with the F450 & F550 Flamewheel kits. The E300 system has 15 Amp ESC's which have an efficient and quick response algorithm allowing for extra maneuverability and stability in wind or during descent, EMF is reduced by using coaxial-cable to power the ESC's which gives a better environment on the airframe for the systems to function.

The E300 kit has the self-tightening propeller system seen on the Phantom 2 series, this prevents incorrect installation of propellers and continually applies pressure to the blades to keep them in place, no more propeller nuts coming off in flight.   

The E300 Tuned Propulsion System comes with:

  • (6) ESC

  • (6) Motor

  • (3) CW Propellers

  • (3) CCW Propellers

  • E300 Specifications: 

System:

  • Recommended load: 300 g/axis

  • Recommended battery: 3S Lipo

  • Maximum Thrust: 600 g/axis

  • Working Temperature: -5°C ~ 40°C Quad or hexa

ESC:

  • Current: 15A Opto

  • Signal Frequency: 30Hz~450Hz

  • Voltage: 11.1V~14.8V

  • Battery: 3S~4S LiPo

Motors:

  • Stator Size: 22×12mm

  • KV: 920 rpm/V

  • Weight: 50g

  • Propellers:

  • Diameter: 24x11cm

  • Thread Pitch: 9.4x4.3 inch

  • DJI Naza V2 GPS Flight Controller Description:

    DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-One design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light weight, small Main Controller. It can measure flying altitude and attitude so therefore can be used for autopilot/automatic control.

    The included plug and play GPS module will greatly enhance the performance for aerial photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.

    The included Naza PMU V2 has enhanced BEC functionality and provides extendable CAN BUS ports, which can support iOSD, Zenmuse H3-2D gimbal (pitch control). Support is also included for optional Bluetooth LED module to allow parameter adjustment via a mobile APP.

    The latest fourth generation attitude stabilization algorithm used by the Naza M V2 not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability even without the GPS module. It is more flexible and stable, and gives the hobbyists a wonderful flight experience. New features have been included such as GPS course automatic compensation, GPS & Compass sensor calibration, new take-off mode and so on.

    Features:

    • All-in-One Design
    • Nine Types of Multi-rotors Supported
    • New Assistant Software for Smartphone
    • Enhanced Failsafe Mode
    • PPM, S-BUS & Ordinary Receiver Supported
    • Multi-rotor One-power Output Fail Protection
    • Independent PMU With Amazing Function Extension
    • Multiple Flight Control Modes/Intelligent Switching
    • iOSD mini supported
    • Two Levels of Low Voltage Protections
    • Independent LED Module
    • Remote Gain Adjustment
    • Advanced & Improved Attitude Stabilization Algorithm 
    • GPS Module Available/Accurate Position Hold
    • Intelligent Orientation Control
    • Motor Arm and Motor Dis-arm
    • Built-in Gimbal Stabilization Function
    • New Assistant Software & Firmware Online Update

    Included:

    Naza-M V2 Main Controller
    DJI GPS/Compass Module
    Naza PMU V2
    Naza Independant LED Module
    USB data cable
    All necessary mounting hardware/connection leads

    Specifications:

    Supported Multi-Rotor: Quad-rotor I4, X4, Hex-rotor I6, X6, IY6, Y6, Octo-rotor I8,V8,X8
    Supported ESC output: 400Hz refresh frequency
    Recommended Transmitter: PCM or 2.4GHz with minimum 4 channels
    Working Voltage Range: MC: 4.8V~5.5V, VU Input: 7.4V~26.0V (recommended 2S~6S Lipoly), Output (V-SEN port red wire): 3A @ 5V (burst current: 7.5A)
    Power Consumption: MAX: 1.5W (0.3A @ 5V), Normal: 0.6W (0.12A @ 5V)
    Operating Temperature: -10°C ~ 50°C
    Assistant Software System Requirement: Windows XP sp3/Windows 7/Windows 8
    Dimensions: MC: 45.5x32.5x18.5mm, PMU: 39.5x27.5x10mm, GPS & Compass: 46mm (diameter)x10mm, LED: 25x25x7mm

    Flight Performance:

    Hovering Accuracy (GPS Mode): Vertical: +/-0.8m, Horizontal: +/-2.5m
    Max Yaw Angular Velocity: 200°/s
    Max Tilt Angle: 35°
    Ascent/Descent: 6m/s, 4.5m/s

  • Tarot T4-3D Brushless Camera Gimbal Description:

The Tarot T4-3D 3 axis, self stabilized gimbal is a professional camera mount for aerial videographers and photographers who want quality and performance.  It has a lightweight, durable aluminium, carbon fiber and plastic structure that will provide outstanding stablility and control for any aerial camera operations even in severe environments.  

The Tarot T4-3D gimbal is designed for GOPRO HERO3 / HERO4 and similar cameras and can be used with multi-copters, fixed wing airplanes and heli-copters.  It is equipped with an independent IMU module and has a "point follow" mode (PF) and a first person view (FPV) mode.

The innovative design allows complete control over the camera. Joystick movement speed is correspondingly linked to camera axis speed, so the faster you move the joystick the faster the axis will move.     

All the power and signal wires are embedded in the structure and the firmware is upgradable through the PC interface.

Features:
• PC interface - Windows XP/ VISTA/7/ 8 (32 or 64 bit)
• Point follow mode (PF)
• First-person view mode (FPV)
• Built-in independent IMU modules
• TAROT PTZ dedicated servo module
• AV output interface
• Wide range voltage input
• Support conventional receiver / S-Bus receiver / DSM receivers
• Supports Camera: GOPRO HERO3 / HERO4 / other similar cameras

Specifications:
Angle control accuracy: ± 0.02 °
Maximum controllable speed: Pitch direction (TILT): ± 200 ° / s
Controllable range of rotation: Pitch direction (TILT): -120 ° to + 15 °
Operating Current: 30mA (@ 25V) 50mA (@ 12V)
Stall Current: 350mA (@ 25V) 700mA (@ 12V)
Working temperature: -20 ° C ~ 50 ° C
Weight: 178g
Size: 99mm × 88.5mm × 105.6mm
Input Power: 2S ~ 6S LiPo battery (Not included)


THANK YOU!