Item Type:DC Permanent Magnet Motor

Item Type:DC Permanent Magnet Motor
Model: 31ZY
Type: Permanent Magnet DC Motor
Rated Voltage: 6-24 (V)
Parameters: (Corresponding to the Table Below According to the Title) Using Voltage V

Operating Voltage (V)	6V	12V	12V	24V	24V	24V
No Load Current (mA)	≤180	≤110	≤350	≤40	≤100	≤200
No Load (rpm)	4000	4000	8000	3500	5000	8000
Rated Torsion (g.cm)	100	100	200	120	200	200
Rated (rpm)	3200	3200	6500	2908	4000	6600
Rated Current (A)	≤0.8	≤0.5	≤1.6	≤2.3	≤0.6	≤1.0
Locked Rotor Torsion (g.cm)	≥500	≥600	≥1000	≥669	≥850	≥1200
Locked Rotor Current (A)	≤3.3	≤2.3	≤6.5	≤1.06	≤2.0	≤4.4

CCM2 DC Motor Regulator Product Output
DC Motor Regulator CW CCW Control
This governor uses PWM control technology, which has the characteristics of high conversion efficiency, wide range and stable performance. All use imported STMicroelectronics original chips, which have been tested for voltage, current, function, etc. before leaving the factory, and the circuit is stable and reliable.
Technical Parameter:
Model: CCM2
Working Voltage: DC10V-30V
Control Power: 12V x 3A=36W, 24V x 3A=72W Greater than 24V, Maximum 120W
Rated Current: 3A
Maximum Current: 5A
PWM Pulse Width Adjustment System Range: 5%-95%
Potentiometer: Resistance Value B10K, Wire Length 20CM, Opening 8mm,
Output Voltage: About 0- of the Input Voltage
Potentiometer is used for regulation
CW CCW switches are used to control CW, CCW, and stop
Note:
Motor
1. When you use the motor, there should be no binding objects. For example, the adhesive should not flow into the bearing through the rotating shaft, which will hinder the operation of the motor.
2. The rotation of the shaft may have the opposite effect on the life of the motor. In order to prolong the life, please check whether your load is in accordance with the regulations. Do not overload or have objects that hinder rotation at the end of the shaft.
3. Manufactured into an eccentric heavy radiation load, which is harmful to the life of the motor.
4. Do not store in surrounding high temperature or extreme humidity, and do not place in corrosive gas, which will reduce the effect of the motor.
5. Do not run the motor in the surrounding high temperature and humidity.
6. When soldering is needed on the positive and negative motor terminals of the power supply, the temperature of the soldering iron is 340℃±40℃, and the heating is within 3 seconds. Do not deform the plastic. Let the soldering spot flow into the motor or break the end of the wire during work. Motor function declines.
7. Do not let the motor shaft get stuck. When the power is supplied, the motor will overheat in a short and its accessories will be burnt.
8. Due to the lack of skills of the staff, the quality of the motor cannot be guaranteed when it encounters the things mentioned in the manual, or the superficial judgment is obviously fault.
9. Supply the specified power and be sure that it is within the range of measurable requirements.
10. The installation of pulleys or gears should not be abnormally aggravated when pressed in.
11. When installing the motor, if the screw is too, it will cause contact between the motor itself and the rotor, which will affect the characteristics.

Governor
1. The input of the DC motor controller is DC, and it cannot be directly connected to AC (such as household 220V AC motors), otherwise it will burn out.
2. The positive and negative poles of the DC power supply cannot be reversed, otherwise the governor will be damaged.
3. The motor can be positive or negative. When the running direction is inconsistent with the expectation, the direction can be changed by adjusting the wire sequence.
4. The potentiometer knob can change the duty cycle of the governor output, thereby changing the motor