Technical Product
Bulletin
Best Value Thermal Grease CPU HeatSink Compound Paste USA
seller- 3 gram Fast
PRODUCT DESCRIPTION:
Heat sink thermally conductive grease compound, used successfully by Ford Motor Company for 20 years, direct replacement for Dow 340 and
Wakefield 120,complies to MIL-DTL-4-7113, less than 30µ particle size, low bleeding, low VOC.
This product is an
opaque white heat sink grease compound, which is applied to the base and
mounting studs of transistor
and diodes to provide a
positive heat sink seal, this facilitates heat transfer away from
electrical/electronic components and
into heat
sinks, thereby increasing the overall efficiency and performance of the
device.
It is grease
like silicone material, heavily filled with efficient heat conductive
zinc oxide and a binding agent, this combination promotes high
thermal
conductivity, high
temperature stability, and the lowest amount of bleed and
evaporation.
This thermal compound
resists changes in consistency temperatures up to 180°C; function as
heat transfer media, durable dielectric insulation, barrier
against environmental
contaminants and as a stress-relieving shock and vibration absorber over a
wide temperature and humidity
range.
This thermal paste
is resistant to ozone and ultraviolet degradation and has good chemical
and solvent stability, good
interference between the
heat producing device and the heat transfer media, and low surface
tension that enables them to
wet most surfaces. It
will not harden, dry, or melt after 1200 hours @ 205°C. Used by Ford
Motors for over 10 years.
ELECTRICAL PROPERTIES:
Dielectric Strength, volts/mil (ASTM D 150) |
390 |
Dielectric Constant @ 100Hz (ASTM D150) |
4.40 |
Dissipation Factor @ 100Hz (ASTM D150) |
0.0021 |
Volume Resistivity, ohm-cm (ASTM D257) |
2.9x1014 |
THERMAL PROPERTIES:
Thermal Conductivity W/m-K |
0.88 |
Operating Temperature Range, °C |
-60 to 205 |
Thermal Resistance °C-In2 /W |
0.05 |
TYPICAL PROPERTIES & CHEMICAL CHARACTERISTICS:
Color |
White |
Base Fluid |
Dimethyl
Polysiloxane |
Filler |
Zinc oxide |
Specific Gravity, 25°C, gm/cc |
2.45 |
Viscosity |
Paste |
Press Flow @ 42.5 PSI, 25°C sec |
13 |
Penetration (Worked), mm |
2851/10 |
Evaporation 24 hrs @25°C, % |
0.0 |
Evaporation @ 200°C 24H by weight,% |
0.5 |
Bleed 24 Hours, % |
0.6 |
POTENTIAL USES:
· Effective thermal coupler for any heat sink device, CPU to heat
sink
· Automotive temperature-sensing devices
· Temperature sensors
· Applied to the
base and mounting studs of
transistor, diodes and silicone
controlled
rectifiers
· Power transistors
· Diodes, semiconductors
· Thermal Joints
· For
any device where efficient cooling is required
· Potting
· TEC Modules
· Hardware
· Telecommunications
· Right product for thermal management
· High-voltage corona suppressant
in connectors for
fly back transferors located in
TV sets.
· Non-Sag or
flowing
· Non-Hazardous polymerization
· Non-Toxic
· Non-Corrosive
· Reworkable
· Easily removed
· Non-Flammable
· Easy to apply via dispensing or screen
printing
· Low surface tension that enables it to wet most
surfaces, which can lower
the thermal contact resistance between
the substrate and material.
APPLICATION METHODS:
Automated or manual dispensing
USAGE INSTRUCTIONS:
For industrial use only Read MSDS carefully prior to use.
LIMITATIONS:
This
compound is neither tested nor represented as suitable for medical or
pharmaceutical use.
STORAGE HANDLING & SHELF LIFE:
This
product has a shelf life of 5 years at room temperature
(76°F) in an unopened container, settlings may occur during long term storage, it is
recommended to re-mix
the filler by hand or mechanical mixing. Keep container tightly closed store
in cool area away from ignition
sources and oxidizers,
no special
precautions need to be taken if product is handled according to directions. Shelf
life is indicated on the
product label,
any special storage
and
handling instructions will be printed on the
product
container label.
CLEAN UP
& DISPOSAL:
This
product can be removed by using solvents such as mineral spirit, heptane, or
isopropyl alcohol. Dispose of in accordance with local, state and federal
regulations for hazardous waste.
SHIPMENT & PACKAGING:
U.S made quality
product - We ship internationally. Multiple use syringe with cap.
This formulation is comparable to or better than Arctic Silver.
PRICES:
|
Thermal Fluid: Silicone
Filler: Zinc Oxide and Binder Agent