General Motors 1964 - 1967 A Body New Flanged Housing 60.5" Stock pinion Location with Big Ford Housing Ends

Wheel mounting flange to wheel mounting flange will be 60.5" with axles installed 

1964-1967 Chevelle, Cutlass, Regal, Lemans, GTO, ect.  60.5" track width with brakes installed.



CHOOSE: 
 GEAR RATIO
 REAR END YOKE SIZE AND
 BOLT PATTERN 
FILL AND DRAIN PLUGS (NONE OR 3/4 NPT IF REQUESTED WHEN YOU ORDER)


**********( WE CAN NOT BUILD UNTIL THE ABOVE OPTIONS ARE CHOSEN!!!)************



  • Ford 9 Inch for 
    A Body New Flanged Housing 60.5" Stock pinion Location with Big Ford New Style Housing Ends.  64-67 GM Midsize Cars.

    Wheel mounting flange to wheel mounting flange will be 60.5" with axles installed (2 1/2" offset axles)

    • Stock rear end pinion yoke location between wheel flanges when center section is installed.  
    • Standard driveshaft location to the right exactly like a General Motors rear.  
    • New Stamped Housing with new 3" x .188" wall DOM tubing.
    • Big Ford New Style (torino) housing ends with .375" (3/8") bolt holes
    • new studs installed in housing

Nodular Iron Trac Loc Center Section 9" Ford with 31 spline US Gear ring & pinion,  Assembled.

FREE Shipping!   The Center Section will be Assembled and set up for Street by Professionals.

ALL NEW UNIT!

  •  Nodular Iron Gear case and Nodular iron Stock size Pinion Support.
  • 9 inch Ford US GEAR 8620 Street Series Ring & Pinion  (ratios 325, 350, 370, 389, 4.11 or 4.30) .
  • 2.89" OD Bearing size x 1.78" ID bearing surface. nodular iron 5 bolt pinion support.   
  • CHOOSE Rear End Yoke: choose 1310  series (3 7/32" wide with 1 1/16" cap OD)  or 1330 series 3 5/8" wide with 1 1/8" cap OD)  rear end yoke.
  • 9 inch Ford PEM 31 spline Trac Loc Carrier (posi clutch style unit)  must use bottle of friction modifier in your lube

Package includes: PEM nodular iron case, iron pinion support, pinion bearings & races, pinion bolts, pinion depth shims, pinion seal, pinion nut, side bearings & races, premium ring gear bolts, tail bearing and tail bearing retainer plate.

All bearings and seals are Premium Brands ( either Timken or Koyo).

Also comes with big housing gasket, u-bolts for yoke and 4 ounce bottle of friction modifier.

We will build this center section after you verify the ratio of ring & pinion and the yoke series you want.

Slotted Econo Rear Disc Brake Kit with Emergency Brake Calipers for 9" Ford

  • This 9 inc Ford Disc Brake Kit kit includes bolt-on caliper brackets
  • 11-1/4" slotted and dimpled vented rotors with 5 on 4-1/2" and 5 on 4-3/4" bolt circles
  • Rotor is 11.25" OD x .960" wide
  • Rotor had hub register of 2.78" OD
  • Rotor has 6.25" Inside Diameter
  • Rotor offset of 2.25"
  • 4.5 bolt circle has 1/2" stud holes and 4.75" bolt circle has 7/16" stud holes
  • The brackets fit the Large Old Style Ford and the New Style Large Torino Housing Ends shown in picture # 11 above. (Kit will be the New Style Large Torino)
  • '78-'88 GM emergency brake calipers, brake pads and hardware.
  • Minimum 15" diameter wheels.
  • Caliper piston size is 2.375" OD.

WARNING: Cancer

And Reproductive Harm-

www.P65Warnings.ca.gov

THIS WILL BE SHIPPED BY TRUCK FREIGHT TO A COMMERCIAL ADDRESS.  MUST HAVE A LOADING DOCK OR A FORK LIFT.