Fuss Receiver Mini Fuss 1 Generation Very Powerful Receiver AFHDS FLYSKY
Really a bit powerful receiver
*Fuss 1 Generation AFHDS Agreement
*Without line weight 1.3g
*4 standard channel, jst1.0mm interface (Nuomoyou has 1.25mm interface servo, you can purchase 1.25 to 1.0 adapter cable, you can plug in the receiver)
*2 channels have brush ESC, one of which 10A ESC and throttle channel (channel 3) linkage; the other 3A ESC is independent 5th channel.
* Default runaway protection function: When the signal is lost, channel 3 and channel 5 are reset to zero, and other channels are back. (that is, the motor will stop and the steering gear will return to the neutral position)
This miniature receiver integrates a very powerful brushed ESC on the third channel.
Core mos is a high current MOS tube designed for low voltage applications
Fully conductive when 2.5v
The resistance is only 3 ohms when conducting
Nominal current 20A
The data is strong enough
The receiver is small and lightweight, designed for small brushed, brushless fixed streams, for the Fuss generation protocol and compatible protocol transmitters. 1S lithium battery power supply or use brushless ESC BEC power supply, the power supply voltage does not exceed 5V.
Instructions:
The receiver does not set the frequency switch and the frequency jumper for reducing the volume, and adopts automatic frequency matching. The receiver automatically enters the frequency mode every time it is powered up. The frequency operation is as follows:
When the receiver is powered on, the receiver LED indicator flashes rapidly for about 15 seconds. The transmitter is turned on before the end of the flash, and the frequency mode is turned on quickly. The receiver receives the corresponding signal LED and immediately turns off, indicating that the frequency is successful. When the transmitter exits the frequency mode, it goes to the normal mode, and the receiver LED lights up to complete the frequency operation. If the signal is not received within 15 seconds, the LED will go out after 15 seconds, and the receiver will be powered again.
The receiver that has completed the frequency does not need to be paired again. After power-on, the LED will flash normally. If the transmitter is turned on after 15 seconds, the LED will be on. If the transmitter is not turned on, the receiver LED will be off after 15 seconds. The LED will also be on for a long time, and the transmitter will be as close as the receiver.
The receiver 20A has a brush ESC channel and a servo three-channel synchronization, all controlled by a throttle lever. The 5A has a small ESC channel defined in five channels, which can be defined as an ESC or switch channel on the transmitter according to your needs.
The receiver does not set the frequency switch and the frequency jumper for reducing the volume, and adopts automatic frequency matching. The receiver automatically enters the frequency mode every time it is powered up. The frequency operation is as follows:
When the receiver is powered on, the receiver LED indicator flashes rapidly for about 15 seconds. The transmitter is turned on before the end of the flash, and the frequency mode is turned on quickly. The receiver receives the corresponding signal LED and immediately turns off, indicating that the frequency is successful. When the transmitter exits the frequency mode, it goes to the normal mode, and the receiver LED lights up to complete the frequency operation. If the signal is not received within 15 seconds, the LED will go out after 15 seconds, and the receiver will be powered again.
The receiver that has completed the frequency does not need to be paired again. After power-on, the LED will flash normally. If the transmitter is turned on after 15 seconds, the LED will be on. If the transmitter is not turned on, the receiver LED will be off after 15 seconds. The LED will also be on for a long time, and the transmitter will be as close as the receiver.
The receiver 20A has a brush ESC channel and a servo three-channel synchronization, all controlled by a throttle lever. The 5A has a small ESC channel defined in five channels, which can be defined as an ESC or switch channel on the transmitter according to your needs.
Packing: IPC
Warranty period: 120 days
Warranty period: 120 days
On Jan-04-22 at 04:46:12 PST, seller added the following information: