Description
Happymodel Mobula7 1S Micro FPV Drone Quadcopter Tiny Whoop (Integrated Receiver for Frsky D8/D16)
Features:
- 75mm whoop based on 1s power
- Flight controller with built-in 2.4G receiver and OpenVTX
- The power of VTX reaches 400mw
- Brand new RS0802 KV20000 brushless motor
- Runcam Nano3: the lightest 800TVL Camera for 1/3 CMOS
- Smooth and powerful
Specifications:
- Brand Name: Happymodel
- Item Name: Mobula7 1S 75mm Micro FPV whoop drone
- Wheelbase: 75 mm (3")
- Size: 99 x 99 x 40 mm (3.9 x 3.9 x 1.6")
- Weight: 24 g (0.05 lb)
Package Included:
- 1 x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame)
- 1 x For X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver
- 4 x RS0802 KV20000 brushless motors
- 1 x Gemfan 1610-2 bi-blade propellers (4CW+4CCW)
- 1 x Runcam Nano3 800TVL camera for 1/3 CMOS
- 1 x Onboard 5.8G Openvtx 0mw~400mw VTX
- 1 x 1S parallel charging board
- 1 x Propeller disassemble tool
- 1 x Extra camera canopy
Note:
- Compatible with 1S Lipo (DC 2.9V-4.35V) / LIHV.
- Batteries are not included. Batteries such as 1S 450mah/550mah/650mah with PH2.0 connector are recommended.
Specifications of Spare Parts:
Motor:
- Mode: RS0802 KV20000
- Configuration: 9N12P
- Stator Diameter: 8mm
- Stator Length: 2mm
- Shaft Diameter: 1.5mm
- Motor Dimension (Dia.*Len): 10.5mm*13.5mm
- Weight: 2.0g
Propellers:
- Weight: 0.24g
- Material: PC
- Pitch: 1 inch
- Props Diameter: 40mm
- Center Thickness: 5mm
- Center Hole Diameter: 1.5mm
Flight Controller:
- For X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
- MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: MPU6000 or ICM20689 (SPI connection)
- Mount hole size: 25.5mm*25.5mm
- Built-in 12A (each) Blheli_S 4in1 ESC
- Built-in OSD for Betaflight (SPI Control)
- Built-in 5.8G OpenVTX 0mw~400mw
- Version for built-in Frsky D8/D16
- Built-in voltage detection
- Built-in current sensor
Onboard 4in1 ESC:
Power supply: 1S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware
Onboard receiver for Frsky SPI D8/D16:
- For SPI BUS receiver Frsky D8
- Compatible Non EU transmitter D8 model
- Channels: 8ch
- No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
- Fail-safe support
Onboard 5.8g OpenVTX:
- Firmware version: OpenVTX
- Smartaudio v2.1
- PIT Mode support
- RCE Mode support
- Channels: 48ch
- Transmitting Power: 0/RCE/25mw/100mw/400mw
- Power supply: DC 5V
- Current (5v): <650ma (400mw)
Runcam Nano3:
- Model: RunCam Nano 3
- Image Sensor: 1/3" for CMOS
- Horizontal Resolution: 800TVL
- Lens: 2.1mm (M8) FOV 150°
- Signal System: NTSC
- S/N Ratio: >50dB
- Electronic Shutter Speed: Automatic
- Auto Gain Control (AGC): Automatic
- Min. Illumination: 0.01Lux at 1.2F
- D-WDR: Automatic
- Day/Night: Color
- Power:DC 3-5.5V
- Current: 110mA at 5V; 120mA at 3.3V
- Housing Material: ABS
- Net Weight: 1.2g
- Dimensions: L14mm*W14mm*H9mm
Features:
- 75mm whoop based on 1s power
- Flight controller with built-in 2.4G receiver and OpenVTX
- The power of VTX reaches 400mw
- Brand new RS0802 KV20000 brushless motor
- Runcam Nano3: the lightest 800TVL Camera for 1/3 CMOS
- Smooth and powerful
Specifications:
- Brand Name: Happymodel
- Item Name: Mobula7 1S 75mm Micro FPV whoop drone
- Wheelbase: 75 mm (3")
- Size: 99 x 99 x 40 mm (3.9 x 3.9 x 1.6")
- Weight: 24 g (0.05 lb)
Package Included:
- 1 x Mobula7 1S 75mm whoop Drone Frame (Mobula7 v4 frame)
- 1 x For X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver
- 4 x RS0802 KV20000 brushless motors
- 1 x Gemfan 1610-2 bi-blade propellers (4CW+4CCW)
- 1 x Runcam Nano3 800TVL camera for 1/3 CMOS
- 1 x Onboard 5.8G Openvtx 0mw~400mw VTX
- 1 x 1S parallel charging board
- 1 x Propeller disassemble tool
- 1 x Extra camera canopy
Note:
- Compatible with 1S Lipo (DC 2.9V-4.35V) / LIHV.
- Batteries are not included. Batteries such as 1S 450mah/550mah/650mah with PH2.0 connector are recommended.
Specifications of Spare Parts:
Motor:
- Mode: RS0802 KV20000
- Configuration: 9N12P
- Stator Diameter: 8mm
- Stator Length: 2mm
- Shaft Diameter: 1.5mm
- Motor Dimension (Dia.*Len): 10.5mm*13.5mm
- Weight: 2.0g
Propellers:
- Weight: 0.24g
- Material: PC
- Pitch: 1 inch
- Props Diameter: 40mm
- Center Thickness: 5mm
- Center Hole Diameter: 1.5mm
Flight Controller:
- For X12 Frsky V1.0 flight controller built-in SPI Frsky 2.4G receiver Target: CRAZYBEEF4FR
- MCU: STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: MPU6000 or ICM20689 (SPI connection)
- Mount hole size: 25.5mm*25.5mm
- Built-in 12A (each) Blheli_S 4in1 ESC
- Built-in OSD for Betaflight (SPI Control)
- Built-in 5.8G OpenVTX 0mw~400mw
- Version for built-in Frsky D8/D16
- Built-in voltage detection
- Built-in current sensor
Onboard 4in1 ESC:
Power supply: 1S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Factory firmware: Z_H_30_REV16_7.HEX
Default protocol: DSHOT300
Support Bluejay firmware
Onboard receiver for Frsky SPI D8/D16:
- For SPI BUS receiver Frsky D8
- Compatible Non EU transmitter D8 model
- Channels: 8ch
- No ground interference ( Transmitter and receiver 1 m from the ground): 200meter
- Fail-safe support
Onboard 5.8g OpenVTX:
- Firmware version: OpenVTX
- Smartaudio v2.1
- PIT Mode support
- RCE Mode support
- Channels: 48ch
- Transmitting Power: 0/RCE/25mw/100mw/400mw
- Power supply: DC 5V
- Current (5v): <650ma (400mw)
Runcam Nano3:
- Model: RunCam Nano 3
- Image Sensor: 1/3" for CMOS
- Horizontal Resolution: 800TVL
- Lens: 2.1mm (M8) FOV 150°
- Signal System: NTSC
- S/N Ratio: >50dB
- Electronic Shutter Speed: Automatic
- Auto Gain Control (AGC): Automatic
- Min. Illumination: 0.01Lux at 1.2F
- D-WDR: Automatic
- Day/Night: Color
- Power:DC 3-5.5V
- Current: 110mA at 5V; 120mA at 3.3V
- Housing Material: ABS
- Net Weight: 1.2g
- Dimensions: L14mm*W14mm*H9mm
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
On Jun 10, 2022 at 00:51:52 PDT, seller added the following information:
