Speedometer Brushless Motor Special Tachometer Speed Sensor Frequency Meter
Feature
1: Adopt industrial-grade high-speed MCU with strong anti-interference
2: Stable and reliable
3: Wide measurement range and high measurement accuracy
4: Small appearance
5: Wide range of applications
2: Stable and reliable
3: Wide measurement range and high measurement accuracy
4: Small appearance
5: Wide range of applications
Newly developed, tailor-made three-phase DC brushless drive products supporting tachometer, using industrial-grade high-speed MCU, strong anti-interference, stable and reliable, wide measurement range and high measurement accuracy, the software adopts the leading full synchronous cycle measurement method, the measurement range It is suitable for all three-phase DC brushless drive boards and drive modules with speed signal output on the market, and has reserved interfaces for plug-and-play with the three-phase brushless drive products independently developed by our store.
Two setting buttons and interface line definition on the back
Note that this product has reverse connection protection. The default power supply voltage is DC 3.3-5V, and the measured signal amplitude is 3-30V. If this parameter is exceeded, it may be permanently damaged.
Details
1. High frequency measurement accuracy, up to 0.01‰ at 25 degrees Celsius, and resolution up to 0.001HZ.
2. Wide frequency measurement range, 0.15HZ—100KHZ. It can also be customized for ultra-low frequency measurement 0.01HZ-100HZ3. The range is automatically switched, from 00.000Hz (R/M to 000.00KHz (KR/M).
4. The working mode can be switched by pressing the button, including two working modes of frequency and speed, and the working mode is saved when power off.
5. The frequency division value can be set by pressing the button. The frequency division value can be 1-99999 and 0.0001-9.9999.
6. Beautiful appearance, sophisticated technology, easy to use.
1. High frequency measurement accuracy, up to 0.01‰ at 25 degrees Celsius, and resolution up to 0.001HZ.
2. Wide frequency measurement range, 0.15HZ—100KHZ. It can also be customized for ultra-low frequency measurement 0.01HZ-100HZ3. The range is automatically switched, from 00.000Hz (R/M to 000.00KHz (KR/M).
4. The working mode can be switched by pressing the button, including two working modes of frequency and speed, and the working mode is saved when power off.
5. The frequency division value can be set by pressing the button. The frequency division value can be 1-99999 and 0.0001-9.9999.
6. Beautiful appearance, sophisticated technology, easy to use.
Specification
Display digits: 5-digit LED digital tube (0.36').
Display refresh rate: signal frequency > 3HZ: 3 times/second: signal frequency ≤ 3HZ: approximately equal to the signal frequency. .
Overflow display: "- - - --"
Measurement accuracy: 0.1%±1digit or 0.01‰ at 25℃.
Measuring range: 0.15HZ—100KHZ. 9r-999.99Kr/m
Input Signal: Type: Dry Contact, PNP, NPN, Pulse Amplitude: 3—30V
Measurement method: full synchronization cycle measurement method.
Input resistance: 100KΩ/resistance.
Power supply: The default DC3.3-5V requires other voltages and can be customized
Withstand voltage: AC2000V 1min between the external terminal and the shell.
Use environment (temperature and humidity): temperature-10℃-+70℃ relative humidity 25-85% (no condensation),
Storage temperature: -20℃-+80℃ (no condensation)
Dimensions (mm): 48*29*18.5 L X W X H)·
Opening size (mm): 45*26
Display digits: 5-digit LED digital tube (0.36').
Display refresh rate: signal frequency > 3HZ: 3 times/second: signal frequency ≤ 3HZ: approximately equal to the signal frequency. .
Overflow display: "- - - --"
Measurement accuracy: 0.1%±1digit or 0.01‰ at 25℃.
Measuring range: 0.15HZ—100KHZ. 9r-999.99Kr/m
Input Signal: Type: Dry Contact, PNP, NPN, Pulse Amplitude: 3—30V
Measurement method: full synchronization cycle measurement method.
Input resistance: 100KΩ/resistance.
Power supply: The default DC3.3-5V requires other voltages and can be customized
Withstand voltage: AC2000V 1min between the external terminal and the shell.
Use environment (temperature and humidity): temperature-10℃-+70℃ relative humidity 25-85% (no condensation),
Storage temperature: -20℃-+80℃ (no condensation)
Dimensions (mm): 48*29*18.5 L X W X H)·
Opening size (mm): 45*26
Instructions
1. There are three lines on the meter head, red is 3.3-5V positive power supply, black is ground line, yellow is signal pulse input line, which are respectively connected with the device to be tested.
2. Rotation measurement and frequency measurement mode switching
There are two buttons "M mode" and "S selection" on the back. When the power is on, press the M button once to enter the mode selection interface, and then press the S button continuously to select 0 frequency plus filter test, and select 1 speed plus filter test. Select 2 frequency unfiltered test, select 3 rotational speed unfiltered test, wait for 4 seconds without operation, automatically save and return to the newly set mode to wait for measurement state.
1. There are three lines on the meter head, red is 3.3-5V positive power supply, black is ground line, yellow is signal pulse input line, which are respectively connected with the device to be tested.
2. Rotation measurement and frequency measurement mode switching
There are two buttons "M mode" and "S selection" on the back. When the power is on, press the M button once to enter the mode selection interface, and then press the S button continuously to select 0 frequency plus filter test, and select 1 speed plus filter test. Select 2 frequency unfiltered test, select 3 rotational speed unfiltered test, wait for 4 seconds without operation, automatically save and return to the newly set mode to wait for measurement state.
Crossover value setting
In the power-on state, short press the S key once to enter the frequency division setting interface. At this time, the S key is the displacement function of the 5-digit 8-character on the display screen, and the M key is to increase the value. key to change the value, the frequency division value must be within 1-99999 or 0.0001-9.9999, other values are invalid (short press the S key to move to the rightmost decimal point, and then short press the M key to turn on or off the leftmost decimal point , to realize the decimal point setting) after setting the frequency division value, wait for 7 seconds without any operation and automatically save and return to the newly set frequency division value and wait for the measurement state.
In the power-on state, short press the S key once to enter the frequency division setting interface. At this time, the S key is the displacement function of the 5-digit 8-character on the display screen, and the M key is to increase the value. key to change the value, the frequency division value must be within 1-99999 or 0.0001-9.9999, other values are invalid (short press the S key to move to the rightmost decimal point, and then short press the M key to turn on or off the leftmost decimal point , to realize the decimal point setting) after setting the frequency division value, wait for 7 seconds without any operation and automatically save and return to the newly set frequency division value and wait for the measurement state.
Explanation of the concept of frequency division value: the number of pulse signals taken by one turn of the turntable or gear during speed measurement. If the brushless driver of our shop cooperates with the speed measurement, if the motor has 2 pole pairs, then the frequency division value can be set to (2*3=6)6.
Precautions
1. It should be used within the parameters of this instrument and in a normal environment.
2. Correctly set the mode according to the actual use requirements and correctly set the frequency division value.
3. When connecting high voltage signal, it is recommended not to operate with power on, and do not touch the chips and parts on the board with your hands.
1. It should be used within the parameters of this instrument and in a normal environment.
2. Correctly set the mode according to the actual use requirements and correctly set the frequency division value.
3. When connecting high voltage signal, it is recommended not to operate with power on, and do not touch the chips and parts on the board with your hands.
List
1 x Speedometer
1 x Speedometer
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Am 07.01.2023 hat der Verkäufer die folgenden Angaben hinzugefügt: