Dental Orthodontic Bonding Bracket Braces Light Cure Primer Adhesive Glue/No-Mix
 
 
 

 
 
Description:  

EXP:12 month or better!

 

Description of Self-Cure Resin:

1. This product is one kind of orthodontic direct bonding system resin with aromatic bis dimethyl acrylate resin as its main material.
2. As a new-type orthodontic direct bonding system, it is convenient to use with little waste, easy to handle independently and has a favorable clinical bonding strength.
3. It consists of primer and paste with acid etchant, spatulas and small brusher as its accessories.

Preparation: Clean tooth enamel surface,eliminate tooth contamination,rinse then isolate tooth and blow-dry.
Etching:Etching the enamel of the tooth with acid etchant for 50 or 60 sec. Rinse and dry with clean air. If the enamel does not have a chalky appearance, pls. repeat the process;
Brushing: apply a thin layer of the primer over the etched enamel with the brusher;
Bonding: apply another thin layer of the paste to seal the edges, adjust the bracket within 20 sec, give pressure for 5 to 10 secand remove the excessive primer and paste after 40 to 60 sec; then do orthodontic procedures followed 5-min curing.

Packaging Detail:
3 x black syringes (3.5g)
1 x primer bottle (10ml)
20 x Brushes



Description of Light-Cure Resin:
Warning: Ortho-Bonding primer and adhesive contains acrylate monomers. Acrylate monomers are known to produce allergic skin reactions in certain sensitive individuals. May cause eye and skin irritation.
Precautions: A void eye and skin contact. Wear gloves when handing this material.
Precaution: Please follow manufacturer's directions on the handing, proper use and recommendations for eye protection, when using a curing light
This system is designed to be used at room temperature (20-25°C, 68-77°F)。Storage between 2-27°C/35-80°F Light Sensitive

 

Contents:
3 x Adhesive paste Syringes (10.5g)
1 x Primer Bottle (8ml)
40 x Brushes
1 x Instruction Booklet



Description of Blue Glue:
This orthodontic adhesive provides a longer working time and a rapid setting time. Can be placed directly into bands. Excess flash is easy to clean up prior to the light curing and the cement is easy to see due to the blue color. 
It contains fluoride to reduce the chance of declacification.

Packing list:
1 x Etchant acid Gel 2.5ml syringe;
1 x Light Cure Adhesive Paste 5g syringe;
1 x Syringe tip 
Box size: 17*11*2.5cm

STORAGE: Store at 25℃ or less in a cool and dry place and avoid direct sun exposure. Recap the syringe after use. 

 

Description of Green Glue：
Reasons for choosing green glue:
1. Green Glue is the two-way color change adhesive for brackets that provides the strength flexibility and intelligent features you demand.
2. Quick-cure polymerization ensure more reliable bond strength 185% more working time than other light cure adhesives allow for better placement.
3. The formula of green glue can improve the impact resistance by 118%, effectively reducing the accidental fall of brackets.
4. Two color change: Heating (Green)----Clear ---Get Cool( Green ), Green---Clear---Green
It is green when the temperature is low, allowing you to clearly identify the excess or residual green glue during the bonding and removal of brackets, so that it can be quickly and accurately removed without damaging the enamel layer. However, after light curing, the color of the green glue will change from green to transparent at normal temperature in the mouth, maintaining a beautiful effect.

 

Packing List:
1 x Adhesive paste Syringe (4g)
1 x Primer Bottle (3ml)
1 x 37%Gel Etchant (2.5ml)
Other accessories

 
Description of  universal Light cure

INDICATIONS FOR USE:
Direct restoration for all class caries.
Restoration of teeth defect and veneer.

Package:
REFILL:
Light Cure Composite: 4g/Syringe*5
Syringe Needles : 5pcs/ box*1
Total Etching Adhesive: 5ml/Bottle*1
Etching Gel: 2.5ml/Syringe*1
Applicators Brushes: 20pcs/box*1
Net weight: 188.4g
COLOR: A1,A2,A3,A3.5,B1

FEATURES & ADVANTAGES:

Unique dispersion technology ensure the filler evenly distributed
Radioopaque and fluoride releasing Optimal polishability and high shade stability.
Excellent handling, not sticky to instrument;
Suitable for most cases of restoration, extensive indication of usage.

INSTRUCTIONS：

(1)Preparation: isolate and prepare tooth.
(2)Cleaning: rinse the preparation with water.
(3)Drying: gently air dry until there is no visible water.Do not allow enamel or dentin to dry for an excessive period of time.
(4)Applying Dentex Self-Etching Light Cure Adhesive (DSA):
dispense 1-2 drops of DSA into a mixing well, apply enough DSA to the entire preparation with a little brush until a shiny surface is achieved and then wait for 10 seconds (DSA should not be applied too much ). Use a gentle stream of air to evaporate the solvent for 5 seconds. (If using a non self-etching adhesive, an etching step should be used according to the manufacturer's instruction).
(5)Cure: light cure for 20 seconds at 500±50mW/cm2. Keep the distance to exposure surface less than 4 mm.
(6)Applying Dentex light cure composite (DLC): place selected DLC into cavity preparation following by light cure. According to following table, the curing time is recommended for different depth and color shades. In order to reduce shrinkage stress, for a large cavity, an increment filling is recommended. In general, 1-2 mm increments are placed into cavity preparation from different sides and the restoration is built incrementally. Each increment is light cured for 30 seconds.
(7) Finishing: after light cure, adjust restoration.
(8) Polishing: use polishing strip or disc to polish the surface

PRODUCT PHOTOGRAPH:  
 
Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand, Thank you!
 
 
The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, do not bid on this item unless you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.
Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand, Thank you!
International Buyers – Please Note
 1. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer’s responsibility.
2. Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.
 
 
 
In the second working day after the paymet has been made. (We will inform you via email if any delay occured due to holiday events.
 
General shipping time is between 7-12 working days. (After the shipping started, the order will be monitored and the track of the item will be posted on paypal.

Destination Delivery Time
Working Days 7-10 10-15 15-25 25-40 >50
US Item arrived 80% 10% 8% 1% Refund
ASIA Item arrived 30% 40% 20% 10% Refund
EU Item arrived 20% 20% 50% 10% Refund
AU Item arrived 30% 30% 20% 20% Refund
other countries Item arrived 5% 10% 10% 60% --
 
 
 
If the item you received is damaged or defective,Please contact us immidately.We will free exchange or refund.
We will pay the return shipping costs if the product is defective or the return is a result of our error. If the item is returned for any other reason you are responsible for the return shipping charges.
You can return your purchase for up to 15 days from the date of delivery. No refund will be issued if the product shows signs of use. Returned package must be in the original packaging, everything must be in new condition, No missing parts.
Our guarantee does not cover accidental damage or wear of product caused by customer.Thank you very much for your understanding!
 
 
  • We will automatically leave a positive feedback to everyone who has completed the transaction and leave us positive feedback.
 
  • Please do not forget to give us Five Stars on all of the Detailed Seller Ratings. Thanks!
 
  • In the unlikely event you are not satisfied with the transaction; please contact us before you submit your evaluation. We believe that everything could be solved by communication.
    1. In order to provide you the best service, please treat the transaction fairly, feedback is simply what we pursue.
    2. Please do contact us first to get a better solution before you would leave a neutral or negative feedback.
    3. We strive for 5-star service by stating upfront our policies, our shipping rate& our shipping frequency. If you were pleased with this transaction, please respond with all 5 stars! If you are not pleased, simply let me know via e-mail rather than leave low score, and I'll work to make it that way. Because leaving me negative feedback does nothing to work out this issue.
    4.     Please email me through 'MY MESSAGES' or "Ask Seller Questions" if you have any question about our listing or your purchase
 
 

  • If you have any problems, we are very glad to help you. We are handling large volume emails every day. Please allow us to reply your email within 24hrs.

  • For the functional products in our shop (such as: Chargers, Data cables), which function is the same as description, but the actual color and shape may look a little different from pictures because of the technical improvement and actual stock state. Please be advised before you bid.