Description
SpeedyBee F405 Wing APP Fixed Wing Drone Flight Controller Supports Vertical Takeoff and Return
Read before purchasing:
- It is the accessories of RC models, not toys. Therefore, safety should come first. If you have any questions, please consult customer service or check the manual.
- Please comply with relevant laws when using this product. Flight in crowded areas is not allowed.
- About battery and charger: Please charge the battery before using. Users who do not know how to wire and set up the charger must consult customer service, because incorrect settings can lead to serious injury. When the battery leaks or is damaged, please do scrap treatment, otherwise it will easily cause fire. Our store is not responsible for safety accidents caused by improper operation by users.
Specifications:
SpeedyBee F405 WING FC Board:
- MCU: STM32F405, 168MHz and 1MB Flash
- IMU (Gyro & Accelerometer): ICM-42688-P
- Barometer: SPL006-001
- OSD Chip: AT7456E
- Blackbox: MicroSD Card Slot
- UART: 6 sets (USART1, USART2, USART3, UART4, UART5 and UART6 (Dedicated for Wireless board Telemetry connection))
- I2C: 1x Used for magnetometer, digital airspeed sensor
- ADC: 4x (VBAT, Current, RSSI and Analog AirSpeed)
- PWM: 12x (11+1 "LED" pad)
- ELRS/CRSF receiver: Supported, connected to UART1
- SBUS: Built in inverter for SBUS input (UART2-RX)
- LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB
- RSSI: Supported, Named as RS.
- Supported FC Firmware: for INAV: SpeedyBeeF405WING(default) and for ArduPilot: SpeedyBeeF405WING
- Weight: 8.9g
SpeedyBee F405 WING PDB Board:
- Input voltage range: 7~36V (2~6S LiPo)
- TVS Protective diode: Yes
- FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip
- VTX BEC output: Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter, Digital Video Transmitter and Camera
- Servo BEC output: Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos
- Weight: 11.4g
SpeedyBee F405 WING Wireless Board:
- Wireless Configuration (long press BOOT button for 6 seconds to switch modes): BLE mode, connect to Speedybee APP; Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.; Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner
- LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes): 4x WS2812 LED strip connectors, adjustable colors and flashing modes
Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads
- On-board electric quantity indicator: 4x RGB indicator LED for electric quantity display by number of lights
- Weight: 4.2g
Note:
- The pin headers needs to be welded.
- Battery is not included in the package.
Read before purchasing:
- It is the accessories of RC models, not toys. Therefore, safety should come first. If you have any questions, please consult customer service or check the manual.
- Please comply with relevant laws when using this product. Flight in crowded areas is not allowed.
- About battery and charger: Please charge the battery before using. Users who do not know how to wire and set up the charger must consult customer service, because incorrect settings can lead to serious injury. When the battery leaks or is damaged, please do scrap treatment, otherwise it will easily cause fire. Our store is not responsible for safety accidents caused by improper operation by users.
Specifications:
SpeedyBee F405 WING FC Board:
- MCU: STM32F405, 168MHz and 1MB Flash
- IMU (Gyro & Accelerometer): ICM-42688-P
- Barometer: SPL006-001
- OSD Chip: AT7456E
- Blackbox: MicroSD Card Slot
- UART: 6 sets (USART1, USART2, USART3, UART4, UART5 and UART6 (Dedicated for Wireless board Telemetry connection))
- I2C: 1x Used for magnetometer, digital airspeed sensor
- ADC: 4x (VBAT, Current, RSSI and Analog AirSpeed)
- PWM: 12x (11+1 "LED" pad)
- ELRS/CRSF receiver: Supported, connected to UART1
- SBUS: Built in inverter for SBUS input (UART2-RX)
- LED: 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator(Red) 1x RGB
- RSSI: Supported, Named as RS.
- Supported FC Firmware: for INAV: SpeedyBeeF405WING(default) and for ArduPilot: SpeedyBeeF405WING
- Weight: 8.9g
SpeedyBee F405 WING PDB Board:
- Input voltage range: 7~36V (2~6S LiPo)
- TVS Protective diode: Yes
- FC BEC output: Output 5.2V +/- 0.1V DC Continuous current 2.4 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed module, Telemetry module, WS2812 LED_Strip
- VTX BEC output: Output 9V +/- 0.1V DC Continuous current 1.8 Amps, 2.3A Peak Voltage adjustable, 9V Default, 12V or 5V via jumper Designed for Analog Video Transmitter, Digital Video Transmitter and Camera
- Servo BEC output: Output 4.9V +/- 0.1V DC Continuous current 4.5 Amps, 5.5A Peak Voltage adjustable, 4.9V Default, 6V or 7.2V via jumper Designed for Servos
- Weight: 11.4g
SpeedyBee F405 WING Wireless Board:
- Wireless Configuration (long press BOOT button for 6 seconds to switch modes): BLE mode, connect to Speedybee APP; Wi-Fi mode, connect to QGroundControl APP, Speedybee APP, MissionPlanner, etc.; Classic Bluetooth SPP mode, connect to QGroundControl APP, MissionPlanner
- LED strip controller (short press BOOT button to switch effects, long press 2 seconds to switch modes): 4x WS2812 LED strip connectors, adjustable colors and flashing modes
Max 5.2V 1.3A, supports around 70pcs 5050 WS2812 LED beads
- On-board electric quantity indicator: 4x RGB indicator LED for electric quantity display by number of lights
- Weight: 4.2g
Note:
- The pin headers needs to be welded.
- Battery is not included in the package.
Payment Terms
1. We accept PayPal,Payoneer,Visa Card,Google pay,Credit card etc.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
2. We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
1. We will process the order within the handling time ,if you have any questions, please contact us via eBay message or email.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
2. For remote regions of DHL/FedEx..., extra shipping costs might be charged. Usually it costs about 30USD-50USD. We will contact you if shipping company informed us your address belongs to remote area. Thanks for your understanding.
Return Terms
If you receive the item that not satisfied or defective, please do not open case and kindly notify us within 30 days. We will guide you the returning process for replacement or refund.
Custom Duties & Taxes
1. It is buyer's responsibility to cover the import duties, taxes.We do not charge any taxes and fees, and the possible taxes and fees will be collected by the platform or by third parties such as customs and carriers.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
2. Please check with your country's customs office and inform us what/how much should declare before shipping.
Feedback
1. Please kindly leave us a positive feedback and 5 star DSR if you satisfied with our product and service. Please feel free to contact us firstly if you have any problem with your order, we are responsible and credible seller and will solve the issue it for you asap.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
On 21/07/2023 at 17:32:27 AEST, seller added the following information:
