100% brand new and high quality!

Woodpecker Xlite 2 Style White/Black
 
Introduction:
1.Technical specifications：
1.1Dimensions: 25mm×25mm×240mm
1.2 Net weight: 280g
1.3 Power source
1.3.1 Power supply: rechargeable Lithium battery
1.3.2 Battery mode: ICR 18490
1.3.3 Battery voltage and capacity: 3.7V/ 1400mAh,Battery has protection against Over-voltage, over-current and short circuit.
1.3.4 Adapter Power Input: 100V to 240V, 50Hz/60 Hz Input Power: 10VA Power Output: DC5V/1A
1.4 Light source:
1.4.1 5W high power blue light LED
1.4.2 Checking method: the LED light is fine when the light is on during operating correctly.
1.4.3 The wave length of this product can match with the clinical dental resin solidification, such as 3M, Dentspl etc.
1.4.4 Wave length: 440nm-480nm
1.5 Light intensity:
P1 mode 2200-3200mW/cm2
P2 mode 1600mW/cm2~2200mW/cm2
P3 mode 1200mW/cm2~1600mW/cm2
2. Operation：
2.1 Press the mode button. Following two modes are available.
2.1.1 TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds.Its output light intensity is about 3200mW/cm2
2.1.2 NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5,10 ,15and 20 seconds.Its output light intensity is about 2200 mW/cm2
2.2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button and the main unit will produce "Bi" sound, the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce tone at every 5 seconds, it stops working when counting down to "0".
2.3 During operation, the blue light can be stopped by press the power button at any time.
2.4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, do not restart until the equipment cool down. Suggest continues working cycle less than 10 times.
2.5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please charge in time.
2.6 When the battery needs to be charged, connect the plug of the adapter into the AC100V~240V power supply. Then connect the output plug of the adapter to the DC 5.0V input plug of the pedestal, and then the logo turn to blue. Put the main unit to the charging point of the pedestal, the display screen turn to scrolling display, and the curing lights starts charging.
2.7 After operating, take off the disposable sleeve and throw away, forbidden to reuse.
2.8 This equipment will turn off automatically if don't any action within 2 minutes, turn it on by press any button.
2.9 The depth of solidification of composite is no less than 2mm per 1 second.
 
Material:The handle is made of plastic，The lamp holder is made of metal
 
Cure 2mm reins in one second
Light intensity up to 2300mw/cm2
 
Features
Constant power output, born for restoration
360 degree rotatable head, extend the possibility
1 sec for curing, Go quicker than ever
ergonomics design, optimize the hand-grip use
 
Basic Data
Battery:3.7V
Power input: AC100V-240V
Colour：White/Black

***********************************************************************************
 
Woodpecker DTE iLED Style (Randomly Color)
 
 
Technical Parameters:
Light Source: Broad Band LED;
Wavelength Range: 385 - 515 nm;
Light Intensity: > 2300mW / cm²;
Battery: Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);
Power Adapter Input Power: AC 100-240V 50 / 60Hz;
Charging time: about 45 minutes;
Size:Handle: Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm (all of the above are the largest size)
Weight: Handle: 96 grams; Charging seat: 99 grams;
Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F);
Operating relative humidity: 30% - 75%;
Operating environment pressure: 700hPa - 1060hPa;
 
Package Contents:
1 × host handle;
1 × charging base;
1 × power adapter;
1 × user manual.
 
Operation and function description:
The entire handle is only one button, light built-in button.
1. For the first time, charge the light curing handle first. Plug the USB cable of the charger into the USB port of the power adapter, plug the power adapter into the power socket, and finally
Put the handle on the charging stand; or, insert the USB cable plug of the charging stand into the USB port of the computer, and then put the handle on the charging stand. Charging instructions are as follows:
| Emerald Flashing | Battery charging;
| Emerald green light | battery fully charged; handle removed the charging seat, the restoration of the previous working mode.
2. Working mode selection, by pressing the button for 2 seconds to release to switch the working mode.
| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW / cm².
| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²
3. Turn the light curing lamp on and off, press the button briefly.
4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby.