Description
Professionals are recommended to install
1.Throttle Body
Throttle Body is a controllable valve that controls the entry of air into the engine, the gas enters the intake tube and mixes with gasoline to become a combustible mixture, which is then burned to form the work done. It is connected to the air filter, the engine block, known as the throat of the car engine.
2.Throttle Body Type
Throttle has two kinds of traditional pull-wire type and electronic throttle, the traditional engine throttle manipulation mechanism is through the pull cable (soft wire) or pull rod, one end connected to the gas pedal, the other end connected to the throttle linkage plate and work.
Electronic throttle is mainly through the throttle position sensor, according to the energy required by the engine, to control the opening angle of the throttle, so as to adjust the size of the air intake.
3.Package Includes:1×Throttle Body&Accessories as shown
4.Compatible Models
1990-1993 Acura Integra GS L4.1834cc
1997-2001 Acura Integra GS L4.1834cc
1992-1993 Acura Integra GS-R L4.1678cc
1994-2001 Acura Integra GS-R L4.1797cc
1986-1989 Acura Integra LS L4.1590cc
1990-2001 Acura Integra LS L4.1834cc
1987-1988 Acura Integra LS Spec Ed L4.1590cc
1986-1989 Acura Integra RS L4.1590cc
1990-1998 Acura Integra RS L4.1834cc
1995-1996 Acura Integra Spec Ed L4.1834cc
1997-1998 Acura Integra Type R L4.1797cc
2000-2001 Acura Integra Type R L4.1797cc
1992-2000 Honda Civic EX L4.1590cc
2001 Honda Civic EX L4.1668cc
1992-1995 Honda Civic Si L4.1590cc
1999-2000 Honda Civic Si L4.1595cc
1997-2001 Honda Prelude Base L4.2156cc
1992-1996 Honda Prelude S L4.2156cc
1995 Honda Prelude SE L4.2259cc
1992-1996 Honda Prelude Si L4.2259cc
1992-1994 Honda Prelude Si 4WS L4.2259cc
1997-2001 Honda Prelude Type SH L4.2156cc
1993-1996 Honda Prelude VTEC L4.2156cc
2000-2003 Honda S2000 Base L4.1997cc
2004-2009 Honda S2000 Base L4.2157cc
2008-2009 Honda S2000 CR L4.2157cc
5.Detail
- Made of High Quality Lightweight Aluminum Body Manufactured with the Latest Permanent Mold Casting Technology and Stainless Steel Materials
- Performance Spec. Racing Design with Multi-Port Injection
- 70mm (2.76"), Much Larger than Stock Body Diameter
- Valve Adopted a Butterfly Plate Mechanism for the Best Control
- High Quality Bearing for Full Manipulation over the Valve and Improved Durability
- Aftermarket Replacement, Instantly Increases HP
- Direct Bolt-On Installation, Simply Weld to the Intake Manifold Flange with the Compatible Bolt Pattern
6.How to clean and prevention needs attention
1.Should be disassembled and cleaned;
2.Correct certain cleaning misunderstandings of the throttle;
3.The formation of throttle dirt mainly from the oil vapor, followed by air particles and moisture, that is, in the use of qualified air filters and remove the crankcase ventilation tube, the throttle spoilage rate will be much slower.
4.The crankcase has a built-in crankshaft and is connected to the oil pan on the lower side, and the operating temperature of this part is around 100° to 180°.
