ESP32 WT32-ETH01 Embedded Serial Port Ethernet WIFI Bluetooth Development Board

Popular

    Product Introduction

    Features
    1.ESP32-ETHO1 is an embedded serial to Ethernet module based on ESP32 series.
    2. Module internal integration of optimized TCP / IP protocol stack, easy for users to easily complete the networking function of embedded devices, greatly reducing the cost of development time.
    3.The module is compatible with half pad and connector through-hole design, the board width is universal width, you can directly weld the module on the board, you can also weld the connector, can also be used for breadboarding, convenient for users to use in different scenarios.
    4.ESP32 series Ic is integrated 2.4GHz Wi-Fi and Bluetooth dual-mode Soc with good functional performance.
    5.The module has super high RF performance, stability, versatility and reliability, as well as ultra-low power consumption.
     
    Specification
    Wi-Fi:
    Protocol: 802.11 b/g/n/e/i (802.11n, speed up to 150 Mbps; A-MPDU and A-MSDU aggregation, support 0.4 _s protection interval)
    Frequency range: 2.4~2.5 GHz
    Bluetooth:
    Protocol: Compliant with Bluetooth v4.2 BR/EDR and BLE standards
    RF: NZIF receiver with -97 dBm sensitivity
    Hardware:
    Network port specification: RJ45, 10/100Mbps, Cross Direct Adaptive
    Serial baud rate: 80~5000000
    On-board Flash: 32Mbit
    Operating voltage: 5V or 3.3V power supply (either one)
    Operating current: 80mA on average
    Supply current: 500 mA minimum
    Operating temperature range: -40°C~+85°C
    Software:
    Wi-Fi Mode: Station/softAP/SoftAP+station/P2P
    Wi-Fi Security: WPA/WPA2/WPA2-Enterprise/WPS
    Encryption type: AES/RSA/ECC/SHA
    Firmware Upgrade: Remote OTA upgrade via network
    Software Development: SDK for secondary user development
    Network Protocol: IPv4, TCP/UDP
    IP acquisition method: static IP, DHCP (default)
    Simple pass-through mode: TCP Server/TCP Client/UDP Server/UDP Client
    User Configuration: AT+ command set
    Size: 63mm*25mm*16mm
    Supply Voltage:
    The power supply voltage of the module can be 5V or 3V3, and you can only choose one of the two.
    Power supply mode:
    Users can choose freely according to the demand:
    1) Through-hole (soldered pins): Power supply by Dupont wire connection; Power supply by breadboard connection;
    2) Half-pad (directly soldered to the board) : Power supply from the user's board.
     
    Instructions for use:
    Power-on instructions:
    If using DuPont cable: find the 3V3 or 5V power input port, connect the corresponding voltage, the indicator light (LED1) will light up, indicating successful power-up.
    Indicator light description:
    LED1: Power indicator, the light is on when the power up is normal;
    LED3: Serial port indicator, when RXD2 (IO5) has data flow, the lamp is on;
    LED4: serial port indicator, when TXD2(IO17) has data flow, the light is on;
    4.3 Usage Mode Description
    Three ways of use, users can choose by themselves according to their needs:
    1) Through-hole (Soldered Pin) : Connect with Dupont cable;
    2) Through-hole (soldered pins): use on breadboard;
    3) Half-pad: Users can directly solder the module on their own boards.
    Description of the working indicator of the network interface
    Green light: Connection status indication, when correctly connected to the network, the green light is on.
    Yellow light: data indication, blinking when the module has data received or sent, including the module received network broadcast packet
     
    List
    1 x Module
    2 x Pin(optional)
    • We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
    • Payment must be received in 5 business days of auction closing.
    • Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
    • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
    • We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
    • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
    • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
    • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
    ESP32 WT32-ETH01 Embedded Serial Port Ethernet WIFI Bluetooth Development Board

    Product Introduction

    Features
    1.ESP32-ETHO1 is an embedded serial to Ethernet module based on ESP32 series.
    2. Module internal integration of optimized TCP / IP protocol stack, easy for users to easily complete the networking function of embedded devices, greatly reducing the cost of development time.
    3.The module is compatible with half pad and connector through-hole design, the board width is universal width, you can directly weld the module on the board, you can also weld the connector, can also be used for breadboarding, convenient for users to use in different scenarios.
    4.ESP32 series Ic is integrated 2.4GHz Wi-Fi and Bluetooth dual-mode Soc with good functional performance.
    5.The module has super high RF performance, stability, versatility and reliability, as well as ultra-low power consumption.
     
    Specification
    Wi-Fi:
    Protocol: 802.11 b/g/n/e/i (802.11n, speed up to 150 Mbps; A-MPDU and A-MSDU aggregation, support 0.4 _s protection interval)
    Frequency range: 2.4~2.5 GHz
    Bluetooth:
    Protocol: Compliant with Bluetooth v4.2 BR/EDR and BLE standards
    RF: NZIF receiver with -97 dBm sensitivity
    Hardware:
    Network port specification: RJ45, 10/100Mbps, Cross Direct Adaptive
    Serial baud rate: 80~5000000
    On-board Flash: 32Mbit
    Operating voltage: 5V or 3.3V power supply (either one)
    Operating current: 80mA on average
    Supply current: 500 mA minimum
    Operating temperature range: -40°C~+85°C
    Software:
    Wi-Fi Mode: Station/softAP/SoftAP+station/P2P
    Wi-Fi Security: WPA/WPA2/WPA2-Enterprise/WPS
    Encryption type: AES/RSA/ECC/SHA
    Firmware Upgrade: Remote OTA upgrade via network
    Software Development: SDK for secondary user development
    Network Protocol: IPv4, TCP/UDP
    IP acquisition method: static IP, DHCP (default)
    Simple pass-through mode: TCP Server/TCP Client/UDP Server/UDP Client
    User Configuration: AT+ command set
    Size: 63mm*25mm*16mm
    Supply Voltage:
    The power supply voltage of the module can be 5V or 3V3, and you can only choose one of the two.
    Power supply mode:
    Users can choose freely according to the demand:
    1) Through-hole (soldered pins): Power supply by Dupont wire connection; Power supply by breadboard connection;
    2) Half-pad (directly soldered to the board) : Power supply from the user's board.
     
    Instructions for use:
    Power-on instructions:
    If using DuPont cable: find the 3V3 or 5V power input port, connect the corresponding voltage, the indicator light (LED1) will light up, indicating successful power-up.
    Indicator light description:
    LED1: Power indicator, the light is on when the power up is normal;
    LED3: Serial port indicator, when RXD2 (IO5) has data flow, the lamp is on;
    LED4: serial port indicator, when TXD2(IO17) has data flow, the light is on;
    4.3 Usage Mode Description
    Three ways of use, users can choose by themselves according to their needs:
    1) Through-hole (Soldered Pin) : Connect with Dupont cable;
    2) Through-hole (soldered pins): use on breadboard;
    3) Half-pad: Users can directly solder the module on their own boards.
    Description of the working indicator of the network interface
    Green light: Connection status indication, when correctly connected to the network, the green light is on.
    Yellow light: data indication, blinking when the module has data received or sent, including the module received network broadcast packet
     
    List
    1 x Module
    2 x Pin(optional)
    • We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
    • Payment must be received in 5 business days of auction closing.
    • Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
    • Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
    • We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
    • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
    • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
    • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.

    DataCaciques