Feature:

1. [Performance] GPU water block adopts copper based structure to provide excellent heat transfer performance and excellent cooling performance.
2. [Waterproof Stable] Using sophisticated production technology, the pump is waterproof, stable and has a long service life.
3. [Strong Heat Dissipation] Equipped with 10 brass pipes of 120mm water drain, which can provide strong heat dissipation.
4. [LED fan] The LED fan has high static air pressure, low noise, and cool lighting effects, and can be used as an excellent choice for computer heat dissipation.
5. [Use] This is a set suitable for desktop computer cooling, suitable for DIY players to assemble their own cooling equipment.

Specification:

Item Type: Water Cooling Kit
Material: ABS, Brass, Aluminum Alloy, Acrylic
Main Accessories:
1. 10 Tube Integrated Water Cooled Copper Bar with LED Fan
Interface: Straight Interface
Fan Size: Approx. 12cm / 4.7in, Approx. 12cm / 4.7in
Fan Interface: Big 4pin
Water Drain Specification: Approx. 120mm / 4.7in
Water Drain Size: Approx. 152mm / 6.0in, Approx. 55mm / 2.2in, Approx. 120mm / 4.7in
2. GPU Water Block
Contact Copper Size: Approx. 50mm / 2.0in, Approx. 50mm / 2.0in
Material: Brass, Aluminum Alloy
Equipped With: 1 Pack of Mounting Screws
3. SC600 Water Pump Components and Pagoda Screws:
Voltage: 12V DC, 3 Pin Plug on the Motherboard
Power: 10W
Head: Approx. 3meters / 3.3yd
Stream Rate: 500 Liters/Hour
4. 140mm Cylindrical Water Tank
Water Tank Diameter: Approx. 50mm / 2.0in
Water Tank Height: Approx. 140mm / 5.5in
Water Tank Material: Acrylic, ABS
Equipped With: 1 Pair of Black Water Tank Brackets, 1 Pair of Silver Brackets, 1 Pack of Mounting Screws
5. Hoses (Transparent) Components
Hose Length: Approx. 2meters / 2.2yd
Hose Size: Approx. 8mm / 0.3in (Inner Diameter), Approx. 10mm / 0.4in (Outer Diameter)
Hose Material: TPE
Equipped With: 1 Pack of Copper Mounting Screws
6. Water Cooled Liquid Filling Device

How to Use:

1. Remove the CPU cooler
2. Remove the CPU base and north bridge
3. The effect picture of removing the CPU base and the north bridge
4. Prepare 4 screws to fix the CPU, and put on spacers for each
5. Put the prepared screws into the four holes of the CPU
6. Turn the motherboard to the front, put a washer on each screw
Screw nuts on 7.4 screws
8. Use a screwdriver to tighten the 4 screws
9. Apply silicone grease evenly on the CPU
10. Align the CPU water block with the hole and place it
11.4 springs are placed on the fixing screws
Tighten the nut with 12.4 screws. The progress of tightening the 4 nuts must be the same, otherwise it will cause imbalance and poor heat conduction.
13. Install 2 pagoda connectors
14. Prepare the two screws of the north bridge, and put washers on the screws
15. The north bridge screw penetrates the hole of the motherboard
16.Turn the motherboard over and put 2 screws on the front side with spacers
17. Apply thermal grease evenly on the North Bridge/South Bridge chip
18. Screw the nut on the screw, go to the back and use a screwdriver to tighten
19. Put the corresponding screws into the North Bridge/South Bridge
20. Put a spring on the screw
21. Screw on the nut, the progress of the two screws is the same, then install the pagoda connector, and tighten
22. The graphics card is removed from the motherboard
23. Remove the previous heat dissipation effect diagram
24. The graphics card head is the same as the previous steps
25. Show that the water block is installed
26. Install the graphics card back to the computer motherboard and fix the effect picture
27. Fix the cooling fan to the cooling water drain (note: the fan is sent to the radiator)
28. The effect diagram of fixing the heat sink on the chassis
29. The display diagram of the follow-up connection of the pump and the water tank. The follow-up method can be changed in the actual situation, and you can install it at will.
30. Fix the water tank rack in the proper position of the chassis, and then snap the water tank into the buckle
31. All accessories are fixed, measure the length of the pipe at each position of the pipeline, and then cut the pipe
32. Put the tube skull on both ends of the tube
33. Casing Skeleton Method
34. Connect the weft waterway like this, and then put the pipe skeleton on the joint with pliers
35. Then check whether each waterway is installed properly to avoid water leakage
36. Add water and coolant, fill the water tank for the first time, and then turn it on, it will become less during the cycle, fill it up again, make sure the air inside is drained, and then plug the plug
37. Connect the power supply of the water pump to the position of the previous CPU fan, and the big 4pin interface of the fan can be found on the power supply to insert it

Package List:

1 x 120 Pagoda Copper Row (with 1 x 12cm Fan)

1 x GPU Water Cooling Head

4 x Long Screws

4 x Finger Screw Nuts

4 x Springs

4 x Small Nuts

8 x Gaskets

1 x Water Pump

1 x 140mm Cylindrical Water Tank

2 x Black Water Tank Brackets

2 x Silver Brackets

2 x Long Screws

4 x Short Screws

6 x Large Nuts

1 x Transparent Hose

6 x Pipe Buckles

6 x Pagoda

2 x Plugs

1 x Docking

1 x Funnel