10Kva Microcomputer High Frequency Inverse Pneumatic Battery Spot Welder 220V Y

 

Application: 
 
Connection , nickel metal hydride and lithium guide wire between the battery and the nickel plate and other aluminum-nickel alloy composite tape , appliance parts and wire welding, all kinds of high or low conductivity of metals and alloys , metal fittings , copper and silver, stainless steel cutlery peripheral accessories combine electronic parts connecting the bulb foot welding, welding buckle. 
 

 

Features: 
 
This machine is designed for the latest high-end design of spot welding spot , is the company 's technology has long been crystallized , according to the principles currently the most advanced designed for spot welding machine adopts microcomputer chip control and AC-DC inverter sticks , performance reached the top level of resistance welding products are the leading domestic peer level , with foreign technical synchronization , can replace foreign products , such as Japan,SEIWA,AVIO,MIYACHI,United States UNITEK Spot welding products. 
 
1,Advanced technology: Continuously combined with international advanced AC-DC inverter technology improvement and innovation to achieve double-pulse welding , the welding and continuous welding pre-pre-solder oxide removal , elimination of debris, reducing the spark ; .. continued solder joint cosmetics firm, no black, uniform spot size burr , does not affect the appearance , the courage and the effect of imported machines Ping Mei. 
 
2,Precise microcomputer control: Long-term high-speed scanning micro-welding the input voltage , a power fluctuations are calculated immediately compensation data , changing the welding energy , so that the welding does not occur due to voltage fluctuations or fried Weld fire phenomenon, to ensure consistent welding results every time , and the small welding sparks impact on the battery is minimal, almost none. 
 
3,Current output stable: Since the machine uses microcomputer chip control , current regulation refinement, ensure that the output current is stable and precise control of welding unrestricted discharge time , every minute of continuous200Several welding, and consistent welding results. 
 
4,Simplified operation settings: Microcomputer of the parameters usedLCDLCD , keyboard adjustment, accurate, intuitive and easy to use. 
 
5,Easy adjustment: Solder pin spacing, pressure independently adjustable for fine original welding, alignment accuracy , high yield. 
 
6,Repairs rate, easy maintenance: Since most of the use of imported machine components, ensure that the failure rate is low , and the machine structure design , maintenance simply replace an integrated circuit board , general mechanics can be replaced. 
 
7,With automatic alarm and cut off system: If the welder is damaged , it will automatically display'Fault',Meanwhile cut the welding circuit to prevent malfunction expand and remind repair. 
 
8,Automatic counting: Single output can automatically count0000-9999,Facilitate the calculation of a single daily output. 
 
9,Copper transformer: Unlike the use of aluminum transformer market , our paragraph copper welding transformers transformers, better conductivity , heat resistance, oxidation resistance stronger , more lasting. 
 

 

Technical Parameters: 
 
1,Power supply: AC220V ± 10% 50Hz ± 2Hz Barometric pressure: 3-4 (KG). 
 
2,Maximum power output: 10KVA. 
 
3,Pre-welding current00-99; Welding time00-30; Welding current: 00-99. 
 
4,Welding trip: 25MM,Weld height freely adjustable , easy to operate. 
 
5,Weight: 40KG. 
 
6,Welding range: Needle welding: 0.03mm-0.6mm Single for welding: 1mmEven thicker. 
 

 

Instructions for use: 
 
1,The output waveform: Reflected pulse state machine at work. 
 
2,Wait.: When the welding current (WI) When adjusting down , the display will appear'Wait.'Prompt , then wait for the whole state appears after a few seconds the program set to work to restore the state. 
 
3,Pre-welding current: (BI) Refers to the height of the first pulse , the size of which is set0-99.Usually choose25About the test machine, the size of the adjustment should be based on the actual welding current welding may be, in general welding current, welding current is correspondingly increased pre. 
 
4,Welding time (WT) : Refers to the width of the second pulse , the total duration of1-30MS,Selected according to the specific effects of the welding time of welding , is usually10-20MS. 
 
5,Welding current (WI) : Refers to the height of the second pulse , which is set in the range of0-99,Usually choose25About the test machine, the size of the adjustment should be based on the actual welding results. 
 
6,Status (STATE) : ON and OFF states vividly shows the photoelectric switch and touch switch at work: The left part of the display'Pneumatic'When the foot switch operation, the right half of the display optical switching state , when the welder in a discharged state , where two switches are'Close'State. 
 
7,Switching (SWITCH) : State switching means switches the display. 
 
8,Cleared (CLEAR) : Press this button to restore the initial state count: '0000 '. 
 

 

 
 
Wed, 22 May 2024 03:43:54 GMT 638519750346808641 9C2F203F04FADB0B20F98AB41122DA5D