ESP-32S ESP32 Module


ESP-WROOM-32 is Powered by Espressif’s most advanced SoC, the ESP-WROOM-32 features high performance, a wide range of peripherals, Wi-Fi and Bluetooth radio, which provide a complete solution tailored to advanced IoT applications.
240 MHz dual core Tensilica LX6 microcontroller with 600 DMIPS
Integrated 520 KB SRAM
Integrated 802.11BGN HT40 Wi-Fi transceiver, baseband, stack and LWIP
Integrated dual mode Bluetooth (classic and BLE)
16 MByte flash
2.2V to 3.6V operating voltage
-40°C to +125°C operating temperature
On-board PCB antenna / IPEX connector for external antenna
Supports sniffer, station, softAP and Wi-Fi direct modes
Max data rate of 150 Mbps@11n HT40, 72 Mbps@11n HT20, 54 Mbps@11g, and 11 Mbps@11b
Maximum transmit power of 19.5 dBm@11b, 16.5 dBm@11g, 15.5 dBm@11n
Minimum receiver sensitivity of -98 dBm
135 Mbps UDP sustained throughput
2.5 µA deep sleep current

Wi-fi	802.11 b/g/n/e/i
	802.11 n (2.4 GHz), up to 150 Mbps
	802.11 e: QoS for wireless multimedia technology
	WMM-PS, UAPSD
	A-MPDU and A-MSDU aggregation
	Block ACK
	Fragmentation and defragmentation
	Automatic Beacon monitoring/scanning
	802.11 i security features: pre-authentication and TSN
	Wi-Fi Protected Access (WPA)/WPA2/WPA2-Enterprise/Wi-Fi Protected Setup (WPS)
	Infrastructure BSS Station mode/SoftAP mode
	Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management
	UMA compliant and certified
	Antenna diversity and selection
	Compliant with Bluetooth v4.2 BR/EDR and BLE specification
Bluetooth	Class-1, class-2 and class-3 transmitter without external power amplifier
	Enhanced power control
	+10 dBm transmitting power
	NZIF receiver with -98 dBm sensitivity
	Adaptive Frequency Hopping (AFH)
	Standard HCI based on SDIO/SPI/UART
	High speed UART HCI, up to 4 Mbps
	BT 4.2 controller and host stack
	Service Discover Protocol (SDP)
	General Access Profile (GAP)
	Security Manage Protocol (SMP)
	Bluetooth Low Energy (BLE)
	ATT/GATT
	HID
	All GATT-based profile supported
	SPP-Like GATT-based profile
	BLE Beacon
	A2DP/AVRCP/SPP, HSP/HFP, RFCOMM
	CVSD and SBC for audio codec
	Bluetooth Piconet and Scatternet

ESP32 vs ESP8266:

ESP32	ESP8266
Ethernet MAC Interface	Nicht vorhanden
GPIOs für 10 Touch-Sensoren	Nicht vorhanden
Temperatur-Sensor (on-chip)	Nicht vorhanden
Remote-Controller-Funktionalität	Nicht vorhanden
Hall-Sensor	Nicht vorhanden
Digital-to-Analog Converter (DAC)	Nicht vorhanden
CAN 2.0	Nicht vorhanden
Analog-to-Digital Converter (ADC): 16 Kanäle mit 12-Bit SAR-ADC mit Unterstützung für einen Low-Noise Amplifier (LNA)	10-bit ADC, kein LNA
2 I2C-Schnittstellen	1 I2C-Schnittstelle
16 Kanäle für PWM	8 Kanäle für PWM
GPIOs (General-Purpose Input/Output): 36	GPIOs: 17
4 SPI-Schnittstellen mit Quad-SPI und maximal 80 MHz	3 SPI-Schnittstellen mit Quad-SPI und maximal 80 MHz

Pinbelegung:

Package included:1*ESP-32 ESP-32S ESP-WROOM-32 WLAN & BLE Module

ESP-32S ESP32 Adapter

This is a adapter board for ESP-32S Wireless Module. It can be inserted to breadboard with Dupont cable wire. Convenient to develop and debug.
RESET I/O Pins
Pin Pitch: 2.54mm

Package included:1*Adapter

ESP-32/ESP-32S Wifi Module+Adapter

Package included:
1*ESP-32 ESP-32S ESP-WROOM-32 WLAN & BLE Module
1*Adapter

ESP-32/ESP-32S Devolopment Board(CP2102)

ESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters,
and power management module. The entire solution takes up the least amount of printed circuit board area.
This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology,
power and RF properties best, which is safe, reliable, and scalable to a variety of applications.
Features:
High performance-price ratio
Small volume, easily embeded to other products
Strong function with support LWIP protocol, Freertos
Supporting three modes: AP, STA, and AP+STA
Supporting Lua program, easily to develop
Package included:1 x ESP32 Development Board