132" (3353mm) x 5/8" Carbon Flex 10R
Starrett Duratec SFB band saw blade.
Flexback is a high performance hard tooth, flexible back carbon steel bandsaw for cutting most materials including wood, plastic and non-ferrous metals.
5/8" (16mm) width x .032" (0.80mm) thickness.
Suitable for: Addison JUB225; Laguna LT-16
Take advantage of our combined postage. Request a total at checkout!!
The correct tooth pitch to use depends upon:
Material type
Size of work piece
Whether solid or a tube or thin-walled section
In
general, cutting thinner materials requires a finer tooth pitch with
more teeth per inch (tpi). Cutting thicker materials requires a coarser
tooth pitch with fewer teeth per inch. A fine tooth pitch cuts more
slowly but with a better quality of cut. A coarse tooth pitch cuts more
quickly but with a rougher quality of cut. Using too fine a tooth pitch
will overheat the blade and shorten blade life. Using too coarse a tooth
pitch will stop the blade or strip teeth.
Note that it may be necessary to vary the tooth pitch used up or down from the recommended value according to experience.
Pitches for Wood-Cutting
Thickness Tooth Pitch
6mm - 12mm 8tpi
12mm - 20mm 6tpi
20mm - 30mm 4tpi
Over 30mm 3tpi
Pitches for Metal-Cutting of Solid Sections
Optimum
tooth pitches for metal-cutting vary considerably depending on the
hardness and toughness of the metal. The recommended pitches shown below
are for solid sections of mild steel. They should be increased (finer
pitch) for tough materials such as stainless steel and decreased
(coarser pitch) for soft materials such as aluminium. See the cutting
chart for more specific recommended tooth pitches for different
materials.
Thickness Tooth Pitch
Up to 6mm 18tpi or 14/18vp
6mm - 12mm 14tpi or 8/12vp
12mm - 25mm 10tpi or 6/10vp
25mm - 75mm 6tpi or 4/6vp
75mm - 125mm 4tpi or 3/4vp
125mm - 200mm 3tpi or 2/3vp
Please look at our other bandsaw & sharpening services..
Carbon Flex Bandsaw blades made to order..
Flexback is a high performance hard tooth, flexible back carbon steel bandsaw for cutting most materials including wood, plastic and non-ferrous metals.
Available in an extensive range of width, thickness, tooth pitch configurations and set patterns.
Blade
length is dependent on the band saw machine being used, To establish
correct blade length, width and tooth pitch please refer to your bandsaw
manual or if in doubt contact North Easst Grinding Ltd for help and advice.
Flexback is a high performance hard tooth, flexible back carbon steel bandsaw for cutting most materials including wood, plastic and non-ferrous metals
Bimetal Matrix (M31/M2) are ideal general purpose metal cutting
and contour cutting of tubing, structures and solids, especially in
fabrication applications or where the material is prone to vibration.
Bimetal M42 blades are used for faster or higher volume production cutting of solid and exotic or tool steels.
As well as suppling quality bandsaw blades we also offer a comprehensive sharpening service for all types of saws, cutters
and DIY tools.
Please look at our sharpening service!!
Our knowledge of grinding and modern grinding
machines helps us to give saws and cutters a superior cutting edge.
At North East Grinding Ltd, we know how to grind saws and cutters,
so we can give you a wear resistant edge that will last longer. Our
wide variety of grinding machines allows us to sharpen saws and cutting
tools matched to new tolerances at a competitive price. We give every
piece we sharpen the personal touch based upon the condition and use of
the item being sharpened.
For further details, please contact:
North East Grinding Ltd
Unit 1, The Old Maltings
Tanners Bank
North Shields
Tyne & Wear
NE30 1JH